routerandswitches

1)     In digital communication systems, a repeater is a device that receives a digital signal on an electromagnetic or optical transmission medium and regenerates the signal along the next leg of the medium. In electromagnetic media, repeaters overcome the attenuation caused by free-space electromagnetic-field divergence or cable loss. A series of repeaters make possible the extension of a signal over a distance.

2)     Repeaters remove the unwanted noise in an incoming signal. Unlike an analog signal, the original digital signal, even if weak or distorted, can be clearly perceived and restored. With analog transmission, signals are restrengthened with amplifiers which unfortunately also amplify noise as well as information.

3)     Because digital signals depend on the presence or absence of voltage, they tend to dissipate more quickly than analog signals and need more frequent repeating. Whereas analog signal amplifiers are spaced at 18,000 meter intervals, digital signal repeaters are typically placed at 2,000 to 6,000 meter intervals.

In the Open Systems Interconnection (OSI) communications model, a switch performs the Layer 2 or Data-link layer function. That is, it simply looks at each packet or data unit and determines from a physical address (the "MAC address") which device a data unit is intended for and switches it out toward that device. However, in wide area networks such as the Internet, the destination address requires a look-up in a routing table by a device known as a router. Some newer switches also perform routing functions (Layer 3 or the Network layer functions in OSI) and are sometimes called IP switches.

On larger networks, the trip from one switch point to another in the network is called a hop. The time a switch takes to figure out where to forward a data unit is called its latency. The price paid for having the flexibility that switches provide in a network is this latency. Switches are found at the backbone and gateway levels of a network where one network connects with another and at the sub network level where data is being forwarded close to its destination or origin. The former are often known as core switches and the later as desktop switches.

In the simplest networks, a switch is not required for messages that are sent and received within the network. For example, a local area network may be organized in a token ring or bus arrangement in which each possible destination inspects each message and reads any message with its address.

Circuit-Switching version Packet-Switching

A network's paths can be used exclusively for certain duration by two or more parties and then switched for use to another set of parties. This type of "switching" is known as circuit-switching and is really a dedicated and continuously connected path for its duration. Today, an ordinary voice phone calls generally uses circuit-switching.

In general, a hub is the central part of a wheel where the spokes come together. The term is familiar to frequent fliers who travel through airport "hubs" to make connecting flights from one point to another. In data communications, a hub is a place of convergence where data arrives from one or more directions and is forwarded out in one or more other directions. A hub usually includes a switch of some kind. (And a product that is called a "switch" could usually be considered a hub as well.) The distinction seems to be that the hub is the place where data comes together and the switch is what determines how and where data is forwarded from the place where data comes together. Regarded in its switching aspects, a hub can also include a router.

1) In describing network topologies, a hub topology consists of a backbone (main circuit) to which a number of outgoing lines can be attached ("dropped"), each providing one or more connection port for device to attach to. For Internet users not connected to a local area network, this is the general topology used by your access provider. Other common network topologies are the bus network and the ring network. (Either of these could possibly feed into a hub network, using a bridge.)

A gateway is a network point that acts as an entrance to another network. On the Internet, a node or stopping point can be either a gateway node or a host (end-point) node. Both the computers of Internet users and the computers that serve pages to users are host nodes. The computers that control traffic within your company's network or at your local Internet service provider (ISP) are gateway nodes.

In telecommunication networks, a bridge is a product that connects a local area network (LAN) to another local area network that uses the same protocol (for example, Ethernet or token ring). You can envision a bridge as being a device that decides whether a message from you to someone else is going to the local area network in your building or to someone on the local area network in the building across the street. A bridge examines each message on a LAN, "passing" those known to be within the same LAN, and forwarding those known to be on the other interconnected LAN (or LANs).

In bridging networks, computer or node addresses have no specific relationship to location. For this reason, messages are sent out to every address on the network and accepted only by the intended destination node. Bridges learn which addresses are on which network and develop a learning table so that subsequent messages can be forwarded to the right network.

Bridging networks are generally always interconnected local area networks since broadcasting every message to all possible destinations would flood a larger network with unnecessary traffic. For this reason, router networks such as the Internet use a scheme that assigns addresses to nodes so that a message or packet can be forwarded only in one general direction rather than forwarded in all directions.

In packet-switched networks such as the Internet, a router is a device or, in some cases, software in a computer, that determines the next network point to which a packet should be forwarded toward its destination. 

The router is connected to at least two networks and decides which way to send each information packet based on its current understanding of the state of the networks it is connected to. A router is located at any gateway (where one network meets another), including each point-of-presence on the Internet. A router is often included as part of a network switch.

A router may create or maintain a table of the available routes and their conditions and use this information along with distance and cost algorithms to determine the best route for a given packet. Typically, a packet may travel through a number of network points with routers before arriving at its destination. Routing is a function associated with the Network layer (layer 3) in the standard model of network programming, the Open Systems Interconnection (OSI) model. A layer-3 switch is a switch that can perform routing functions.

An edge router is a router that interfaces with an asynchronous transfer mode (ATM) network.

Routers and switches are both computer networking devices that allow one or more computers to be connected to other computers, networked devices, or to other networks.