Issue Description

Q: How does the Huawei ADSL users on different service boards of different 

Huawei MA5600 (MA5600 V300R002) DSLAMs access each other?

Alarm Information

null

Handling Process

A: ADSL users on different service boards of different MA5600 DSLAM can access each other under the same smart vlan.According to the construction of the MA5600 DSLAM users are able to connect with each-other directly. The two MA5600 DSLAM ports are not isolated over layer 2. For example: 1. PC1 is connected to the port 0/15/7 on MA5600_A, and PC2 is connected to port 0/15/23 on MA5600_B of the  H563ADGE board. 2. The IP address of  PC1 is 192.168.2.1/24, and the IP addressPC2 is 192.168.2.2/24. 3. Both user's  PC1 and PC2 belongs to smart VLAN100. 4. The ADSL RTU works in the 1483B mode, with VPI/VCI being 0/35. Data Configuration: MA5600_A(config)#vlan 100 smart MA5600_A(config)#port vlan 100 0/7 0 MA5600_A(config)#service-port vlan 100 adsl 0/15/23 vpi 0 vci 35 rx-cttr 0 tx-cttr 0 MA5600_B(config)#vlan 100 smart MA5600_B(config)#port vlan 100 0/7 0 MA5600_B(config)#service-port vlan 100 adsl 0/15/7 vpi 0 vci 35 rx-cttr 0 tx-cttr 0

Suggestions

ADSL users can access to each other under the same smart vlan of different MA5600

1, Huawei ADLE

2, Huawei MA5600

More related:

1,  Abnormal fiber power causes GP1A E1 service test failed

2,  How Do I View Statistics about ACL Resource Usage?

Configure the IP address of the inband NMS interface.Create the LS-S2318TP-EI-AC  NMS VLAN.huawei(config)#vlan 10 standardAdd the upstream port.huawei(config)#port vlan 10 0/7 0-2Enter the NMS VLAN interface mode.huawei(config)#interface vlanif 10Configure the IP address of the NMS VLAN interface.huawei(config-if-vlanif10)#ip address 10.10.1.2 255.255.255.0Add the route.Configure the route destined to the NMS (trap destination host).huawei(config)#ip route-static 2.2.2.2 255.255.255.255 10.10.1.1preference 1huawei(config)#ip route-static 2.2.2.3 255.255.255.255 10.10.1.1preference 1Configure the route destined to the time server.huawei(config)#ip route-static 4.4.4.0 255.255.255.0 10.10.1.1preference 1Configure the route destined to the log host.huawei(config)#ip route-static 3.3.3.0 255.255.255.0 10.10.1.1preference 1huawei(config)#ip route-static 3.3.4.0 255.255.255.0 10.10.1.1preference 1Add the ACL rule to implement the traffic classification.huawei(config)#acl 3050huawei(config-acl-adv-3050)#rule permit ip source any destination anyhuawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.20.0.0.0huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0destination 10.10.1.2 0.0.0.0huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0destination 10.10.1.2 0.0.0.0huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.4 0.0.0.0destination 10.10.1.2 0.0.0.0huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.5 0.0.0.0destination 10.10.1.2 0.0.0.0huawei(config-acl-adv-3050)#rule permit ip source 3.3.3.3 0.0.0.0destination 10.10.1.2 0.0.0.0huawei(config-acl-adv-3050)#rule permit ip source 3.3.4.3 0.0.0.0destination 10.10.1.2 0.0.0.0huawei(config-acl-adv-3050)#quithuawei(config)#packet-filter inbound ip-group 3050 port 0/7/1huawei(config)#packet-filter inbound ip-group 3050 port 0/7/2Configure the SNMP parameters.Configure the community name and the access rights.huawei(config)#snmp-agent community read publichuawei(config)#snmp-agent community write privateConfigure the administrator ID and contact information.huawei(config)#snmp-agent sys-info contact HW-075528780808Configure the device location information.huawei(config)#snmp-agent sys-info location Shenzhen ChinaConfigure the SNMP version.huawei(config)#snmp-agent sys-info version v2c NOTE:Here, the SNMP version must be the same as the SNMP version of the NMS. In this example, the NMS SNMP version is set to SNMP V2C.Enable the trap sending.huawei(config)#snmp-agent trap enable standardSet the trap destination address.huawei(config)#snmp-agent target-host trap-paramsname p1 v2c securityname publichuawei(config)#snmp-agent target-host trap-hostname aaa address 2.2.2.2 trap-paramsname p1huawei(config)#snmp-agent target-host trap-paramsname p2 v2c securityname publichuawei(config)#snmp-agent target-host trap-hostname bbb address 2.2.2.3 trap-paramsname p2Set the trap source address. huawei(config S2326TP-EI )#snmp-agent trap source vlanif 10

DOCSIS 3.0 defines various DOCSIS events, such as authentication failure and CM certificate error events. Configuring DOCSIS event reporting helps you obtain MA5600T/MA5600/MA5608T and CM running status. The following configurations are used as an example to configure the CM management feature:Priority of DOCSIS events: alertMode of reporting DOCSIS events to the U2000: trapMode of reporting DOCSIS events to the log host: syslogIP address of the U2000: 10.10.10.10IP address of the log host: 10.10.20.10huawei(config)#cable event alert report traphuawei(config)#snmp-agent target-host trap-hostname huawei address 10.10.10.10 trap-paramsname docsishuawei(config)#cable event alert report syslog huawei(config)#cable event loghost ip 10.10.20.10

More related:

How To Reset Huawei OLT MA5600T Series Equipment Password

Implementation of TR069 protocol in MA5600 series

Optical attenuation is too large lead to ONU recovery failure

Ethernet Basics_GFP, VCAT, and LCAS-V1.0

The opening Configuration of MA5603T / MA5600 Equipment, the similar products include MA5600T

HW5615#config terminal

HW5615 (config) #hostname games

HW5615 (config) #atmlan ip-add e 10.253.***.*** 255.255.255.252

HW5615 (config) #atmlan ip-route 0.0.0.0 0.0.0.0 10.253.***.***

HW5615 (config) #atmlan ip-access 10.253.0.0 10.253.255.255 255.255.0.0 (in the absence of ACL equipment is unable to PING gateway)

HW5615 (config) #nms 300

HW5615 (config) #int LAN 0/0

HW5615 (config-LAN-0/0) #uplink-select fiber (set MA5615 to port part)

HW5615 (config-LAN-0/0) #vlan 3656 common

HW5615 (config) #pvc LAN 0/0 36560 disable ADSL 0/1/1 040 off off 33

HW5615 (config) #pvc LAN 0/0 36560 disable ADSL 0/1/2 040 off off 33

HW5615 (config) #pvc LAN 0/0 36560 disable ADSL 0/1/3 040 off off 33

HW5615 (config-LAHW5615 (config-LAN-0/0) #cascade forward all (cascade through all VALN)

HW5615 (config-LAN-0/0) #cascade number 3 (cascade 3 level)

N-0/0) #default-vlanid 300 (upper port is VLAN300 untag port)

Change the device IP address:

The first step: delete routing HW5615 (config) #no atmlan ip-route 0.0.0.0 10.253. * *. * * *