#ma5603t

Huawei OLT MA5600T MA5603T Board Configuration

Board Configuration(MA5600T/MA5603T)

This topic describes the type, name, slot and mapping of the boards supported by the MA5600T/MA5603T.

HUAWEI OLT MA5608T Price

MA5600T Price

MA5603T Price

 NOTE:

This manual describes the supply of boards supported by the product. However, the availability of the boards is subject to the PCNs. For the availability of the boards, contact…

The integrated fiber-copper access platform and the access-aggregation integration capability of the Huawei MA5600T/MA5603T/MA5608T effectively ensure the smooth evolution of the access network.

The MA5600T/MA5603T/MA5608T supports integrated fiber-copper access and access-aggregation integration, as shown in Figure 1.

Fiber-Copper Integration

The Huawei MA5600T/MA5603T/MA5608T enables optical fibers and copper lines to be integrated in one platform, which ensures that the access network can smoothly evolve from copper line access to optical fiber access.

Optical fiber access: The MA5600T/MA5603T/MA5608T supports GPON, 10G GPON, and P2P optical fiber access, satisfying the requirements of the FTTH, FTTB, FTTC, FTTO, FTTM, and FTTW scenarios.

HetAN

The Huawei MA5600T/MA5603T/MA5608T serves as the CO OLT and supports multiple network construction modes and diversified access media to provide access for home users, mobile users, and enterprise users. Such a heterogeneous access network (HetAN) wins popularity.

User access: provides access for home users, mobile users, and enterprise users.

Network construction mode: supports FTTH, FTTB, FTTC, FTTW, FTTO, and FTTD networks.

By adding the WDM1r component, the MA5600T/MA5603T can be smoothly upgraded from GPON to 10G GPON.

Carriers can newly construct a 10G GPON network or upgrade a GPON network to a 10G GPON network, as shown in Figure 1. Specifically, the WDM1r component is added to the OLT so that GPON and 10G GPON signals can be transmitted over the same ODN in the multiplexing mode.

MA5600T Huawei 

The MA5600T is an integrated fiber-copper access device, and can serve as a DSLAM, OLT, or aggregation OLT.

The MA5600T, if serving as a large-capacity DSLAM, supports ADSL2+, VDSL2, SHDSL, and POTS access modes.

The MA5600T, if serving as a large-capacity OLT, supports GPON, 10G GPON, and P2P access modes.

The MA5600T, if serving as an aggregation OLT, supports FTTB/FTTC/DSLAM aggregation access, which simplifies the network architecture, reduces types and number of devices, and minimizes the CO equipment room space and energy consumption.

The networking mode of the line optimization is similar to the networking mode of the NMS. The MA5680T /MA5603 can communicate with the N2510 in the outband or inband mode. This topic considers the networking in the outband mode as an example to describe the communication between the MA5600/MA5603 and the N2510. Configure the IP address of the maintenance network port.huawei(config)#interface meth 0huawei(config-if-meth0)#ip address 10.10.20.10 255.255.255.0Add the outband NMS route.huawei(config-if-meth0)#quithuawei(config)#ip route-static 10.10.21.0 24 10.10.20.254Configure the related SNMP parameters.Configure the community name.huawei(config)#snmp-agent community read publichuawei(config)#snmp-agent community write privateConfigure the administrator ID and contact information.huawei(config)#snmp-agent sys-info contact HW-075528780808Configure the device location information.huawei(config)#snmp-agent sys-info location Shenzhen ChinaConfigure the information about the SNMP version.The configured version must be consistent with the SNMP version set by the N2510. Assume that the SNMP version used by the N2510 is SNMP V3.huawei(config)#snmp-agent sys-info version v3Enable the trap message sending.huawei(config)#snmp-agent trap enable standardConfigure the IP address of the target host contained in trap messages.huawei(config)#snmp-agent target-host trap-paramsname p1 v3 securityname publichuawei(config)#snmp-agent target-host trap-hostname aaa address 10.10.21.10 trap-paramsname p1Specify the IP address of the maintenance network port as the source address for sending the trap messages.huawei(config)#snmp-agent trap source meth 0Save the data.huawei(config)#saveConfigure the line optimization.After the MA5600/MA5603 and the N2510 are successfully interconnected, you need to create the line optimization task on the N2510 to enable the line optimization. For the information about how to operate on the N2510, see "8 Line Optimization" in the N2510 Configuration Guide. After the N2510 delivers the operation to collect the parameters, the MA5600/MA5603 collects the parameters of the port to be optimized. According to the collected parameters, the N2510 provides the optimization profile. You can deliver the optimization profile to the MA5600/MA5603 automatically or manually. In this manner, the line optimization is implemented.

Contact information:

Telephone: 852-30623083

Email: [email protected]

        [email protected]            

Website: http://www.thunder-link.com

More blog:

Huawei Low-end Switches Boot Upgrade For BOOTROM

Huawei Low-end Switches Upgrade The APP System

Cisco-Router-IOS Configuration Backup And Recovery

The opening Configuration of MA5603T / MA5600 Equipment, the similar products include MA5600T

HW5615#config terminal

HW5615 (config) #hostname games

HW5615 (config) #atmlan ip-add e 10.253.***.*** 255.255.255.252

HW5615 (config) #atmlan ip-route 0.0.0.0 0.0.0.0 10.253.***.***

HW5615 (config) #atmlan ip-access 10.253.0.0 10.253.255.255 255.255.0.0 (in the absence of ACL equipment is unable to PING gateway)

HW5615 (config) #nms 300

HW5615 (config) #int LAN 0/0

HW5615 (config-LAN-0/0) #uplink-select fiber (set MA5615 to port part)

HW5615 (config-LAN-0/0) #vlan 3656 common

HW5615 (config) #pvc LAN 0/0 36560 disable ADSL 0/1/1 040 off off 33

HW5615 (config) #pvc LAN 0/0 36560 disable ADSL 0/1/2 040 off off 33

HW5615 (config) #pvc LAN 0/0 36560 disable ADSL 0/1/3 040 off off 33

HW5615 (config-LAHW5615 (config-LAN-0/0) #cascade forward all (cascade through all VALN)

HW5615 (config-LAN-0/0) #cascade number 3 (cascade 3 level)

N-0/0) #default-vlanid 300 (upper port is VLAN300 untag port)

Change the device IP address:

The first step: delete routing HW5615 (config) #no atmlan ip-route 0.0.0.0 10.253. * *. * * *

How to Configure ARP Detection: Huawei MA5600T, MA5603T and MA5608T

Prerequisites

The access device provides upstream ports through the upstream boards. ARP detection is not supported if the access device provides upstream ports through the control board.

A Timedelay protection group is configured on the upstream boards. For configuration details, see Configuring an Ethernet Port Protection Group.

  Figure shows an Ethernet port protection example in which the access device (MA5600T/MA5603T/MA5608T) is dual-homed to BRASs.

  The MA5600T/MA5603T/MA5608T is dual-homed to BRAS 1 and BRAS 2. The working links

are Link1 and Link2, and the protection link is Link3. If Link1 is faulty and Link2 is normal,

the MA5600T/MA5603T/MA5608T can switch services to Link3 by using ARP detection even

though the upstream port on the MA5600T/MA5603T/MA5608T is functioning properly. This

ensures uninterrupted service transmission.

  Configuration:

Step 1 Configure VLAN and Layer 3 port IP address for ARP detection.

1. Create a VLAN.

Run the vlan command to create a smart VLAN for ARP detection.

2. Add an upstream port to the VLAN.

Run the port vlan command to add the working upstream Ethernet port in the protection

group to the VLAN. The protection port in the protection group cannot be added to the

VLAN.

3. Create a Layer 3 interface for the VLAN.

Run the interface vlanif command to create a Layer 3 interface for the VLAN and enter

the VLAN interface mode.

4. Configure an IP address for the Layer 3 interface in the VLAN.

Run the ip address command to configure an IP address for the Layer 3 interface in the VLAN. Ensure that this IP address is in the same subnet as the IP address of the remote device.

  Step 2 Configure ARP detection for the working port in the protection group.

1. Configure ARP detection for the working port in the protection group.

Run the arp-detect command to configure ARP detection for the working port in the

protection group.

2. (Optional) Configure the times for sending ARP detection packets.

Run the detect-multiplier command to configure the times for sending ARP packets. If

the remote device does not respond to the ARP detection packets sent by the local device (here, the access device) for the specified times, the local device considers ARP detection has timed out.

The waiting time for ARP detection is derived from the following formula: Waiting time = Interval for sending ARP request packets x Times for sending ARP packets. The ARP detection waiting time is also the time taken for triggering a protection switching. The minimum waiting time is 3s (1s x 3). Because the interconnected devices have to process

ARP packets, the device CPU load will increase. The more frequent the packets are sent, the heavier the CPU load.

3. (Optional) Configure the interval for sending ARP detection packets.

Run the min-tx-interval command to configure the interval for sending ARP detection

packets.

4. Enable the ARP detection function.

Run the detect enable command to enable the ARP detection function.

  Step 3 Configure ARP detection for the protection port in the protection group.

Repeat Step 2(but change the working port to the protection port) to configure ARP detection for the protection port in the protection group.

  Step 4 Verify ARP detection configurations at the two ports in the protection group.

Run the display arp-detect command to verify ARP detection configurations, such as the remote

IP address and enable/disable status of ARP detection, at the two ports in the protection group.