#cord protector

My Cord Protectors with my Remax 610D Part 2 by ~murumokirby360

The installation protective earphone is finally done. 😊🔊🎶

And in case that you missed it then please click theses links down below. 😉 ↓

• My Cord Protector for my Remax 610D (with Chowder and Panini) - [10/21/19] Part 1 • My Cord Protector for my Remax 610D (with Chowder and Panini) - [10/23/19] Part 2 •My Cord Protector for my Remax 610D (with Chowder and Panini) - [1/31/20] Part 3 (FINAL)

My Cord Protector for my Remax 610D (with Chowder and Panini) - [10/21/19] Part 1

Well here’s my 1 of 2 parcels have finally opened as I promised and thus I’m revealing it right off the bat without recording another video (yeah well because of ‘time management’ but nevertheless). 😊

So allow me to explain about this item I ordered since 3 months ago:

From 1st to 4th Images:

•What you see here was the ‘cord protector’, and what’s the purposed you asked? Well this prevent from bending and messing tangled wires from any wired items such as my Remax 610D earphone which I’ll get to that later. Usually the problem was the copper wired inside on any existing wired items which is became useless or not respond for audio earphones from bending and tangled which result the copper wire snapped, but when it wear the cord protector through their wired item by circling it’ll never happened and hope it’ll lasts. 

From 5th to 7th Images:

•Here what you see here was my Remax 610D earphone, It’s been 1 year old now. As of now I haven’t used it since because I’ve been so much time using my Awei A780BL headphone so now my earphone was borrowed by the hands of my little brother (*sigh* seriously he should buy his own earphone now rather than borrowing mine)... Take a look of my audio jack, the white part of the wire was bit busted and a half just ripped off also it was bit messed due to using and surprisingly it still fine and function with some slightly difference on the sound quality.

From 8th to 10th Images:

• So how to install this cord protection on the functional wire? Well; First - cut both ends (using a pair of scissors) of the clump, second - once cut the clump you may now place your functional cord and twirl it with your hands, and third - keep twirl continuously until it’s done and repeat the process to make sure that your functional wire is completely covered and unique look. You can combine two or three colors if you’re desire, like mine right here. It takes around 10 to 30 minutes to install the cord protector depending of what functional cord wire (e.g. USB Cable, Audio Jack and Earphone) you desire so patient is key.

NOTE: Though if your don’t get it at all then please play this video.↓

(See 10th Image) Though there are so many cord protectors I have I only have 10 photos to shown ya. And yes my paper dolls just joined in on every photos I took and they liked my cord protectors - I don’t know why but I always bring my paper dolls for some unique, heheh. ^^;

My Cord Protector for my Remax 610D (with Chowder and Panini) - [1/31/20] Part 3 (FINAL)

This is my part 3 and my final part of installing my cord protector for my Remax 610D. 😊

If you haven’t seen my clean and fresh liked new version look from last year then please [CLICK ME].

BTW: With a total of 15 pictures I took, some of my photos are now combined into one image (by using GIMP) - just so fit in to 10 photos limited.

I have finally free time to continue my installing my cord protector for my old and yet functional Remax 610D. 😁

1st to 4th images:

•As you might a guest I still have a completed pieces of unused cord protector with the exception of two because I’ve already installed from my previous part. So now I’m picking two black colors this time around.

5th Image:

•But before I installed on the other side, it seems that the wiring beside the earpieces (both Left and Right) are now wear off from unwanted over bend - or at least from storing in my bag. But miraculously it still functional only with a slightly different audios but hey, close enough. 

6th to 8th Images:

• After 10 to 20 minutes of twirling the cord protector both of earpieces and wires are now secured, I even make a double twirl on the right side beside the remote button. All was good except the half was not enough.

9th Image:

•Thankfully I have another cord protector I could pick and thus the white color; wear on each sides, double twirl it and cut the excess. 

10th Image:

•Voila! Success! My installation is finally completed, I’m now gladly to used my old earphones in a long lasted protection. My paper dolls are now happy to hear! 😊

And I’m happy to say that I’m closing this topic right now and continue on with my other upcoming stuff.

So that’s the end of my topic about installing cord protector to my earphone (Remax 610D), and in case you missed my previous parts then check out my links down below.↓ 😉

My Cord Protector for my Remax 610D (with Chowder and Panini) - [10/23/19] Part 2

This is my part 2 of installing my cord protector for my Remax 610D. 😊

BTW: If you haven’t seen my clean and fresh liked new version look from last year then please [CLICK ME].

1st and 2nd Image(s):

•Now with continuing on my process, as you can see once again I only have 8 cord protectors remaining so now I gonna need one more to fill that cord I’ve covered since yesterday. Hope my paper dolls watching this. ^^

3rd and 4th Image(s):

• I picked once again another related blue color to install the half of the wire, and here’s what I’m talking about fusing colors before - by twirling the cord to make a connected fused color plus its completely secured so it won’t come off (I guess). 

• After a tons to twirling the cord it is done, I could either cut the excess or just leave it anyway but I have another idea which is my next image(s).

5th to 7th Image(s):

• So in order to uncut  the excess cord protector I decided to double it with the same process and result is completely secured, so what do you know this part is completely protected, yay!

8th Image:

•And uh I didn’t mentioned this from yesterday though, I used a super glue to make a lock between two cord protectors. Somehow I shouldn’t do this but it’s too late, and hey at least I could remove it with acetone but for now this method I made could be stay intact.

9th and 10th Images:

•So far the first part was completely covered and it seems my paper dolls impressed me, so thanks. 😊 So now on to the left and right wired earpieces including the three buttons (located on the right earpiece) but that’s gonna be another day.

Well that’s all for now, more part(s) on that coming soon.😉

My Cord Protectors with my Remax 610D Part 1 by ~murumokirby360

I'll be continue this topic coming up soon. 😊🔊🎶

So in case that you missed it then please click theses links down below. 😉 ↓

Prevent Those Frayed Charging Cords With ChargeGuardZ

Most people have cell phones these days. And, along with cell phones comes the charging cord. The good thing about charge cords is that they’re more interchangeable these days. Remember when they weren’t? The bad thing about charge cords is that they seem to wear out over time (especially near the connectors).  But, what if I told you that you can help prevent charge cords from getting damaged…

Pelindung Kabel, apalagi ini?

Ada-ada aja ya aksesoris gadget jaman sekarang. Dulu waktu masih booming Nokia, gantungan yang suka menyala kalau ada sms masuk aja udah keren banget, eh ternyata sekarang udah usang ketinggalan jaman.

Nasib kabel charger iPhone 3GS

Akhir-akhir ini lagi tren pelindung kabel charger yang terbuat dari plastik lunak berbentuk spiral dengan warna-warni cerah yang fungsinya nanti adalah melilit kabel…