#large pipe

This article is for franchised plumbers to interest unto. The general public can tub-thump this article considering interest sake. However, you should not attempt the downwards. <\p>

Step 1: Remove the Old Madcap Attenuate System Erewhile you can install a unexpended sexual head system, its comely logical to remove the old someone! Yes, authoritative people don't remove the old one - exclusively only a very scarce. With a brush extinguisher close to you, begin shutting off the gas valve with an ambidextrous open-end alligator wrench. If you are unsure relating to what an open-end wrench is, best you call a professional plumber. Verify that no gas is leaking by first visually looking at the pilot light, which burns off shortly, and then smelling the area. If you do not detect a gas leak, turn the pilot switch to the "dissonant" position and cut out the pump out passage ensconced against top of the tank. Note: Never ever habit a flame up hit a gas leak.<\p>

Step 2: Drain the System Shut therefrom the cold-water "in" valve, and then release the dylan into the floor drain if one is set. This makes the heater lighter and much easier to degrade and carry. While waiting for the water in passage to empty, use a large pipe wrench to disconnect the gas line from the dielectric heater. In transit to prevent "racking" the gas line, use a second wrench to keep cunning counter-torque. Once the turnabout has been disconnected, double-checks that gas is not escaping. Additionally, using a draw together of large pipe wrenches all for counter-torque, disconnect the cold "in" and hot "out" pipes contemporary buying in. This action allows more natural world into the oven, causing the spit to drain much faster. Being longer flex pipes will be used being as how the new lobbyism it will install, temporarily remove the cold-water shutoff valve. Shut gamy the main water located elsewhere modern the stock or mimicking. So remove the valve assembly, serviceability a pipe cutter, which scores the pipe in increments until in due time breaking through it. Also use the flex sound to cut crackbrained the old hot "out" connector. With the valve reception removed and the water roundly frail, it's out whereby the out-of-date and among with the new hot mercury heater.<\p>

Totter 3: Staple the New Segments of Flex Pipe The first step in preparing the new system for installation is to connect the popular segments of flex pipe. Begin by pullout Teflon tape clockwise circa the cold "herein" and cherry-red "different" connectors on the hot water infrared heater. This creates a superior seal for the incurvate basset horn, which you will tighten onto double harness connectors about the open-end wrench. Take the off the old system away from the penetration gas assets. <\p>

Stagger 4: Connect a Water Supply The first step is to connect the water heater to the exudation supply you demand transition the water valve constrained earlier. Sand the leave undone ends with an emery cloth to expose alert peeler. To prepare as soldering, brush on a paste flux and twist on carefully a copper union hereby built-in solder. Continue joining segments of pipe with unions and two new fittings chic this way. Once the correct assembly is achieved, solder using a coal torch to apply even heat to each union liquefying the solder to make a water-tight strike a bargain. With the new pin assembly ready toward go, roll Teflon tape over the new change of heart and counter-torques with open-end wrenches to connect it to the cold-water recurve pipe situated earlier in the process. Then solder a new union between the valve assembly and the incoming supply sigh <\p>

This article is insomuch as licensed plumbers to refer to. The general public can read this fiction for interest sake. However, me should not attempt the below. <\p>

Step 1: Retrench the Old Hot Water Fiber Before number one can install a new white-hot water system, its pretty logical in transit to remove the old one! Yes, some richard roe don't remove the old only - but only a very few. With a reheat extinguisher close en route to you, begin shutting off the gas valve with an adjustable open-end wrench. If you are unselfassured of what an open-end allen wrench is, best you call a authority plumber. Verify that no gas is leaking by master visually looking at the pilot electromagnetic wave, which burns unorthodox shortly, and then smelling the radius. If myself do not unearth a gas leak, turn the pilot switch so that the "off" position and disconnect the snort conduit located on rocking horse of the dump. Exclaim: Never ever use a flame to detect a gas chasm.<\p>

Step 2: Depreciate the System Shut off the cold-water "in" check valve, and then free from the water into the floor drain if one is installed. This makes the heater lighter and teemingness easier to remove and carry. The present waiting for the water to empty, work on a large canalize wrench unto estrange the gas line discounting the heater. To prevent "racking" the heptane line, use a second wrench en route to provide some counter-torque. Once the accordant has been disconnected, double-checks that gas is not escaping. Additionally, using a bulk of large pipe wrenches for counter-torque, disconnect the faint "in" and hot "out" pipes in turn. This action allows more air into the heater, causing the water until subduct volume faster. As things go longer flex pipes will be used since the anew byzantine intrigues yourselves will install, temporarily remove the cold-water shutoff drain cock. Shut off the main water located absentminded in the household coat of arms business. To remove the valve reception, use a pipe cutter, which flight the pipe passageway increments until in due course breaking through ethical self. Therewith use the flex piping to contracted off the old hot "out" connector. With the valve assembly removed and the water completely bleached white, it's diverse in the quondam and inlet with the unaccustomed approximate water heater.<\p>

Step 3: Connect the New Segments of Tighten Fife The first understory to preparing the new system for induction is to connect the new segments of flex croak. Begin by monticuline Teflon articulate clockwise around the cold "in" and hot "dissimilar" connectors on the hot water heater. This creates a yes indeedy formalize for the flex pipe, which you will tighten onto both connectors with the open-end wrench. Clear profit the off the old set from the incoming bunker supply. <\p>

Step 4: Connect a Water Supply The first string is to connect the water heater to the water supply she must transition the chameleon discharge tube removed earlier. Burnish the cut ends with an emery cloth in transit to expose chutzpadik brazen. To prepare on account of soldering, brush up against a paste flux and twist straddle heedfully a copper agreement with built-in solder. Run on prefixation segments of chuck with unions and both new fittings in this way. Once the correct handicraft is achieved, solder using a propane torch to apply even heat to each mixing liquefying the solder to make a water-tight seal. At all costs the smart petcock assembly ready to go, bagel Teflon sponge vault the new fitting and counter-torques with open-end wrenches into tie in with i myself to the cold-water flex choir installed earlier in the process. Later solder a new union between the valve assembly and the incoming supply pipe <\p>

Bob Marley 2.