#teila

Brand

Zoomlion/CIFA

Chassis Brand

Hino700

Model

Hino700

Released date

2010

Fob price(Appreciated with customer proposal and negotiation price)

USD25000

Drive mode

6*4

Cabin

GreyFS2844, 3seats

Engine

Model

Hino E13C WB

Emissionstandard

Euro5

Max output power(Kw/rpm)

321/1900

Max torque(N·m/rpm)

2059/1800

Transmission

Model

RTLO16918B 18 forward 4 reverse

Rear axle: ratio/loading capacity

V Rod Left Rear/21.8 tons

Clutch

Hino CR-380,Drytwin plate with damper springs

Braking system

Full air, dual circuit

Main Parameter

Overall dimension(mm)

9000*2500*3930

Mixer barrel volume

10m³

Wheelbase(mm)

4005+1350

GVW(Kg)

25000

Rated load (kg)

11870

Tire

11.00R20

http://www.hnteila.com/concrete-mixer-truck/zoomlion-cifa-hino700-concrete-mixer-truck.html

With the rise of modern industry, the construction method of concrete as the main material has become one of the main constructions in the construction industry, It takes up a large proportion in all kinds of engineering construction, this makes the development of concrete machinery durable, and there is a growing situation. Trailer mounted concrete pump, referred to as "trailer pumps", it is one of the various concrete machines, used for conveying and pouring in concrete construction.

 Generally, a concrete delivery pump has the following main technical parameters: delivery capacity, outlet pressure, power, and distribution valve form. In terms of power type, pump trailer is generally divided into diesel trailer pumps and motor trailer pumps. In terms of hopper allocation, trailer pumps are generally divided into S valve, Ram valve, C valve.

 Classification selection 37kW (domestic minimum standard concrete pump, under 37kW is fine stone mortar pump), 45kW, 55kW, 75kW, 90kW, 110kW, 130kW (diesel), 132 kW, 162kW (diesel), 174kW (diesel)......

 Trailer pump is manufactured by electric, diesel and ultra-high pressure for your use on sites. The trailer Mounted Pumps prove their worth and superior performance in various applications, e.g. operate well at -22°C in Moscow, 55°C in Dubai, 12h continuous pumping and pump of difficult concrete like B90, C150, and 3-gradation concrete. 5 core pump technologies provide you with the best trailer pump. Trailer pump has high pumping efficiency, long service life, simple operation, efficient energy saving, cutting-edge technology, trustworthy!

http://www.hnteila.com/concrete-pump/concrete-trailer-pump/

Our own number: 723

1. Re-manufactured Putzmeister 42 meters concrete pump, Volvo chassis, 4RZ boom form with x-leg. First-level standard maintenance. High working stability.

2. Approximate to New putzmeister used pumps standard.

 Safety issues should be paid attention to in the construction of putzmeister used putzmeister pump

Keep the water tank full of clean water, and check and deal with it in time when finding the water quality is cloudy and there are many sand grains.

Bolts of the putzmeister 42m shall be fastened, pipe joints shall be tightly sealed, and protective devices shall be complete and reliable.

The control, high-speed handle, handwheel, control lever and cock shall be in the correct position. The hydraulic system should be normal and free of leakage.

When the pumping system is under pressure, it shall not open any delivery pipe or hydraulic pipe. The safety valve of the hydraulic system shall not be adjusted arbitrarily, and the accumulator can only be filled with nitrogen.

After the operation of concrete tow pumps, all the commercial concrete in the hopper and pipeline must be exported, and then the putzmeister concrete pump truck, hopper and pipes shall be cleaned. When rinsing the pipe with compressed air, no one can stand within 10 meters in front of the outlet end of the pipe, and the foam rubber and sand particles rushed out should be collected by metal net basket.

It is strictly forbidden to flush the pipe of the placing boom with compressed air. The folding and shrinking of the placing boom should be done in order.

http://www.hnteila.com/concrete-pump/putzmeister-42m-concrete-boom-pump.html

1. Putzmeister 42 meters concrete pump, Volvo chassis, 4 axle x-leg, classical 4 booms, high working stability.

2. Manufacture Date is November of the year 2005.

3. Maintenance completed new tires of the complete machine. Hopper maintenance; Finishing lubrication pipeline, circuit, and hydraulic circuit. Whole line arrangement, old pipe and line changed, pressure debugging for 8 hrs and in very excellent condition.

4. Import quality, trustworthy. No formalities and higher cost performance.

5. The first class of machine and make sure each of everything is in good condition, must zero fault when leaving the factory, reduce working pressure and cost from clients.

 Only with the stable lower plate is the pump truck safe. The arm-frame pump truck supporting leg should be paid much attention.

 Just like kung fu, if your "lower plate" is not strong enough, you can easily be pushed down. Whether Putzmeister second hand pump trucks' legs can firmly "plunge" on the ground, is the priority of the safe operation of the arm gantry pump truck.

 1. Protect yourself and others from dangerous areas

When opening or closing the leg of the gantry Putzmeister stationary concrete pump, the rotation range is a dangerous area. People may be hurt in the range. When carrying out this operation, you should be careful of yourself and the people nearby.

 2. To strengthen of the overlapping location is great. The supporting legs should be extended in place.

The legs of the arm pump truck all have fixed strengthening positions. Only when the legs are opened and extended in place can these strengthening positions give full play to the strength. Otherwise, the supporting legs will be in danger of breaking. Pay attention to the arrows on the legs and ears as you extend them.

 3. Communicate with construction personnel in advance and don't "step on empty"

The gantry pump truck must be supported on a solid ground. If the maximum pressure of the supporting leg is greater than the allowable pressure on the ground, the supporting plate or auxiliary square shall be used to increase the supporting surface area. In addition, communicate with the person familiar with the construction site before supporting the leg, and make sure the leg is not above the sewer.

 4. Keep a safe distance to prevent ground collapse

Adequate safety distance should be set aside to prevent ground collapse when support is near a pit or ramp.

 5. The arm pump truck must be leveled and must not exceed 3 degrees

After the support is completed, make sure that the maximum horizontal deflection of the gantry Putzmeister truck mounted concrete pump is no more than 3 degrees. Generally speaking, the direction of the extension of the arm frame will be raised higher during the construction process, leaving a surplus for the subsidence after the extension of the arm frame. Currently, the arm mounted pump truck is usually equipped with an electronic level and alarm device. Once the arm mounted pump truck tilts too high, the alarm will sound to remind the operator. Before extending the armrest, make sure the legs are properly attached.

 6. Remote control ensures the safety. Do not be too high from the ground

Upon confirmation of all the leg under the condition of reliable and efficient, make confirmation on the leg safety with the first and second boom. The specific approach is to stretch one arm frame, making the open Angle at 90 degrees. Then let two booms in one meter off the ground. Move one arm up and down in the position of four legs, check whether the corresponding arm bracket and diagonal arm bracket are safe.

 7. If water enters under the leg, the arm shall be returned for safety

In case of the occurrence of rain water, oil cylinder leakage of supporting legs and factors reducing the stability of supporting legs, the arm shelf should be closed immediately. After the problem is eliminated, the supporting legs should be put up again according to the requirements.

 In addition, when supporting the arm pump truck, it is better to keep the tire off the ground by 5 cm or so. Otherwise, the swing of the s swing tube of the arm pump vehicle and the shaking of the vehicle caused by the impact of pressure in the tube will damage the vehicle driving mechanism.

http://www.hnteila.com/concrete-pump/putzmeister-concrete-boom-pump-736.html

Advanced and exquisite maintenance and remanufacture technology. Maintenance and remanufacture technology leads the industry. Teila Remanufacture has introduced the industry-leading standard system of "one, two, three, four and five level", strictly in accordance with standard procedures for maintenance and inspection, implementing the process operation, standardizing the management, to ensure customers feel comfortable to purchase and use. What is re-manufacturing? Re-manufacturing is guided by the product life cycle theory, and in order to achieve the goal of improving the performance of waste products, in accordance with the principles of high quality and high efficient, energy and material saving, environmental protection, by means of advanced technology and industrialization production, we take parts of the refurbished pumps (remanufactured) and then repair it , and a series of technical measures of transformation of waste products or the floorboard of the engineering activities. Construction equipment re-manufacturing is not a simple repair, we can think the re-manufacturing as the highest stage of the repairing. The common repair is where it breaks, we fix it. But the re-manufacturing is a serial activity of repairing with the high technology and industrialized production. Frankly speaking, Teila dismantles the pump and then according to the standard of re-manufacturing, repairs, assembles and debugs it.

 What is refurbishing? Refurbishing is guided by the product whole life cycle theory, and in order to realize the waste product performance improvement as the goal, with the rule of high quality and high efficient ,energy and material saving, environmental protection, by means of advanced technology and industrialization production, we take parts of the equipment and then repair it , and a series of technical measures of transformation of waste products or the floorboard of the engineering activities. Concrete pump refurbishing is not a simple repair, we can think the refurbishing as the highest stage of the repairing. The common repair is where is broken, repair it. But the refurbishing is a serial activity of repairing with the high technology and industrialized production. Teila dismantles the refurbished concrete pumps and then repair, assemble and debug it according to the standard of refurbishing.

http://www.hnteila.com/concrete-pump/refurbished-concrete-boom-pump/

Our own number: 535

1. Re-manufactured Sany 45 meters concrete pump, Isuzu chassis, 4RZ boom ground jack is leg lifting. First-level standard maintenance. High working stability.

2. 20 hours pressurized with water and debugging, exempted from inspection in perfect condition. New tires, new paint, overall maintenance for engine and hopper, just change nozzle, glasses plates, cutting ring, piston replacement. debugging and rectification to good condition.

3. Sany Quality+ Sin Hanyo Re- manufacture It's more reliable than buying a second line brand new Sany pump concrete.

 The glass plate is an important part of the sany concrete pump manual. Although its volume is small, its technical content and processing cost are very high. At present, glass plate can serve for about 30,000 cubic meters of commercial concrete pumping. In order to improve the service efficiency of the arm gantry pump truck, it is very important to take corresponding measures to improve its service life.

 Working characteristics of glasses plate

The eyeglass plate is a part of the S-shaped Sany truck mounted concrete pump distribution valve, connecting to the commodity concrete conveying cylinder. Driven by the swinging oil cylinder, the moving part S pipe swings from one commodity concrete cylinder to the other commodity concrete cylinder. The cutting ring vibrates with the S-tube attached to the eyeglass plate. The quick swing of the cutting ring causes intense wear between the eyeglass plate and the pre-mixed concrete. It also bears the impact of cutting off the stones. It can be seen that the eyeglass plate mainly works at room temperature and bears the impact force, shear force and very strong friction.

 The main failure modes of eyeglass plate are wear and fracture failure. The wear between the eyeglass plate and cutting ring is abrasive wear. First, the cutting ring and the hole Angle of the eyeglass plate are blunt, and a smaller circular surface wedge-shaped trace is formed. The wear gap increases with the increase of abrasive particle size. When the gap is large to a certain value, the construction will be affected by severe leakage of the slurry. With the increase of pump height, the impact shear of the eyeglass plate will increase, the wear will be more intense, and it is prone to fracture and collapse.

 It can be concluded from the above analysis that the surface of the eyeglass plate should not only have high hardness and wear resistance but also have the certain toughness and high fracture resistance.

http://www.hnteila.com/concrete-pump/sany-48m-concrete-boom-pump.html