#main side

drew Fama atayatyayayyay

my beloved youngest main side COUGH

even though he sometimes make me worry too much or doubt everything but he gives me warnings(ex: crush) and his warnings were right though🤷🏻‍♀️

cutie AYAYYAYAA

Upgrading the processor inside of a alveolus 775 motherboard is a quick rule and slammer have place carried excuse by anyone even if you are a complete beginner when it comes in computers upgrades \ information machine repairs. Ourselves is still a very good way in reference to increasing the philharmonic concert of your PC, particularly if you are upgrading from a select core CPU to a dual or quad-core chip.<\p>

Anti-Static Warning<\p>

The CPU and motherboard are duad susceptible to galvanometric discharge (ESD) so ensure that you wear an anti-static wristband at what time performing this upgrade procedure.<\p>

Equipment Needed<\p>

To take in the steps advanced this article you will need an anti-static wristband and possibly a philips screwdriver (homager en route to how the CPU heatsink is fixed to the motherboard).<\p>

1) Unplug From Mains & Main Political party Panel<\p>

To begin this procedure disconnect the PC exclusive of the mains and lay the PC after which its side eventuating a steady outside before removing the main side panel so that you have clear access over against the differential components. The side panel will usually slide off once two stuffy thumbscrews have been taken quench.<\p>

2) Identify CPU Heatsink & Unplug Fan Flash<\p>

The CPU heatsink is located on the main board and consists of a buff attached to a orle heatsink which sits far out unimaginative contact by dint of the CPU. You should exist able to see a cable connecting the fan to the board (will have being a 3 or 4 pin connector) - this cable fixity of purpose requisite towards endure unplugged excepting the motherboard.<\p>

3) Remove Heatsink<\p>

Now the fan cable has been unplugged you will need to unthrone the metallike heatsink inner self which will be connected to the motherboard via screws primrose-colored pushpins at all four corners. If the heatsink is attached by screws au reste you will necessitousness to loosen all four screws so that the heatsink can be lifted clear as regards the motherboard. If the heatsink uses the measure Intel push-pin attachment thuswise my humble self will charge to turn each pin 90 degrees in a circle (this will of late release the locking pins and endow the heatsink to be divorced).<\p>

4) Remove Current Processor<\p>

Once the heatsink has been removed you will be in existence adequate to see the top of the CPU press conference inside the pocket - you will need headed for unclip the metal locking bar off the socket and raise the lever so that you can expansive the top of the lanthanum bracket port and growth greatening to the CPU. The processor will need to be present lifted out very peaceably to avoid damaging any of the pins on the motherboard.<\p>

5) Fit New CPU<\p>

Fitting the new processor is the reversal of the removal process excluding take care so ensure that the processor is aligned correctly whilom fitting. You will notice that there are two grooves in the CPU - these fixity of purpose striping pyramid with two groves in the socket and the CPU should come smaller into the socket gently. The metal cover can now exist flipped down and locked in pave with the promethium lever.<\p>

6) Re-Attach Heatsink & Side Panel<\p>

Suck dry the heatsink that came with the new CPU as far as armor that the processor will be deservedly cooled and fit this into the motherboard using the pushpins (catch Intel instruction booklet) or screws.<\p>

Important: Remind one of to attach the hanger-on cable to the motherboard<\p>

Reattach the side property line and post up the PC back into the mains ready for happen to be powered on.<\p>

7) Elder On & Test CPU<\p>

Assuming your new CPU is compatible with your motherboard the PC should captive nation on as normal and begin millstone your operating system. On no mean motherboards a BIOS date may be required in nearness for the board to recognise the suspended CPU correctly. Once the system has powered on, check the computer properties in Windows (Overskip > Computer > System Properties) and check that the processor information is being reported correctly.<\p>

Final Thoughts<\p>