#face board

Hey look it's the artist no one likes

I did this and it by some miracle someone wants to request I will gladly do it

Grape pergolas are a handsome piece of architecture easily built off the side of any home. Plant a couple of grapevines and watch the entire pergola come to life, offering you cool shade in the summer and beautiful grapevine shadows on your patio in the dead of winter. In the Middle East, grapevines growing on pergolas are used as natural air condtioning. Water is sprayed on the grapevines of the pergola and people sit underneath and enjoy the cooling air as the water evaporates into the atmosphere. You can do the same thing.

Instructions

1. Cut the 12-foot board to length and nail it horizontally to the side of the house over the doorway, making sure it's level.

2. Dig two holes in the ground at least 12 inches deep at the front two corners of the pergola. Mix up one bag of concrete per hole using a rubber tub, water and a hoe. Set the posts in the holes and check for plumb--that the posts are standing straight up and down--and shovel the concrete into the holes. Brace the posts and allow the concrete to set.

3. Run a level line from the top of the horizontal board nailed to the house to each post. Hang a string level on the line. Move the string up or down on the post until the string reads level. Mark the line on each post with pencil and draw straight right angle lines across the posts using a metal square. Cut the tops of the posts off with a circular saw.

4. Notch out the front facing top of both posts. The notch will accomodate a 4x6 face board set on edge.

5. Cut the 2x6 board to length and set up on the two notched-out posts on edge. Attach the face board to the posts with carriage bolts.

6. Cut the 2x6 rafters to length and nail them to the face board and ledger board that is nailed to the house. Set a rafter every 16 inches for the full width of the pergola.

7. Measure the distance between the rafters. Cut 10 cross pieces of 2x6 lumber to that measurement. Nail these between the rafters. Line them up with each other all the way across the width of the pergola so when all are nailed in place, it looks like two, parallel, continuous rafters.

8. Climb up a ladder and on top of the pergola. Wherever a cross piece connects to a rafter, lay a 1/2 by 5-inch flat galvanized nail plate over the union and nail in place.

9. Cut 12 pieces of 2x6 board at 15 3/4 inches long. Draw out a paper pattern 15 3/4 inches wide by 6 inches high. From the right end of the long edge of the paper, measure in 4 inches and mark. On the top left, measure down 1 1/4 inches and mark. From the 4-inch mark, measure straight up 2 inches. Lay the metal square down on the paper and connect the 1 1/4-inch mark with the 2 inch mark and draw a line--the line will be at an angle. Cut out the pattern.

10. Lay the pattern on each 15 3/4 inch piece of wood and transpose the design. Cut along the lines with a saw.

11. Nail one decorative end piece on the face plate at the end of each rafter on the front. On each side, nail a decorative end piece at every point where a cross piece is nailed to the outside two end rafters.

Tips Warnings

A string level is a small plastic level that hooks onto a string to run a level line.When the bubble in the tube of the level sits right in the middle of the tube, the string is level.

Related Posts:

Build A Septic Tank Baffle PVC pipeA baffle is a vital part of your septic tank, preventing solid waste from entering the field lines and also from backing up into the house drain. If the baffle has been damaged, knocked of...

Build A Mud Set Shower Pan Build a Mud Set Shower PanFollowing the proper steps when building a shower pan is critical to avoid expensive leaks down the line. The following guideline is an industry best practice.Instruction...

Build A Cell Phone Repeater The two types of repeaters are passive and active. Passive repeaters have no amplifier and pass information from one antenna to another via cable. Active receivers also use antennas and cables; ho...

Make Your Own Vinyl Banners Event bannerWhether you're celebrating a birthday, school reunion or another event, you can create a banner announcing the event where many people can see it. It can also be used as a means to mar...