#ecu simulator

New Generation of SAE J1939 ECU Simulator Board With ESP32

Our SAE J1939 gateway allows you to monitor, simulate, and record any PGN as defined in the SAE J1939-71 Standard but also including diagnostic messages according to SAE J1939-73.

Arduino-Compatible OBD-II CAN-Bus ECU Simulator with Teensy 3.2

The OBD-II CAN-Bus ECU simulator uses the Arduino-compatible Teensy 3.2 module (included). It helps test the OBDII interface and write diagnostic software. ECU PIDs parameters are adjustable via menu options.

SAE J1939 Data Recorder - Programming And Data Retrieval

The following is an update on our activities regarding our development of an SAE J1939 data recorder. The development affects two of our devices, the  SAE J1939 Gateway Module With USB Port, RTC, MicroSD Memory Card and the SAE J1939 Gateway And Data Logger With Real-Time Clock.

Both gateways are supported by our free-of-charge jCOM1939 Monitor, an SAE J1939 Monitoring, Analyzer and ECU Simulation software under Windows.

SAE J1939 Starter Kit And Network Simulator

Our JCOM.J1939 Starter Kit And Network Simulator is designed to allow the experienced engineer as well as the beginner to experiment with SAE J1939 data communication without the need of connecting to a real-world J1939 network, i.e. a diesel engine. It may sound obvious, but in order to establish a network, you need at least two nodes, and that fact applies especially to CAN/J1939 where the CAN controller will basically shut down after transmitting data without receiving a response. For that reason, our jCOM.J1939 Starter Kit And Network Simulator consists of two J1939 nodes, namely our jCOM.J1939.USB, an SAE J1939 ECU Simulator Board With USB Port.

The jCOM.J1939.USB gateway board is a high-performance, low-latency vehicle network adapter for SAE J1939 applications. The board supports the full SAE J1939 protocol according to J1939/81 Network Management (Address Claiming) and J1939/21 Transport Protocol (TP).

SAE J1939 Data Logger Produces Excel-Compatible Files For Further Processing

Our free-of-charge JCOM1939 Monitor Software for Windows is a complete tool to monitor, analyze, record, and simulate SAE J1939 data traffic. It works in combination with our SAE J1939-USB gateways.

The monitor software represents a comprehensive and easy-to-use, easy-to-understand tool that displays not only SAE J1939 data traffic; it also allows scanning the network, simulating an ECU (incl. full node address negotiation features), and responding to data request messages.

SAE J1939 Monitor, Analyzer, And ECU Simulator For Windows - New Byte & Bit Editing Mode

The jCOM1939 Monitor Software by Copperhill Technologies is the ideal software tool for monitoring, analyzing, and simulating SAE J1939 data traffic.

The program links to our jCOM.J1939.USB ECU Simulator Board that operates as an SAE J1939 to USB (or UART) gateway.

This comprehensive and easy-to-use, easy-to-understand Windows software illustrates not only SAE J1939 data traffic; it also allows the scanning of the vehicle network, simulating an ECU (incl. full node address negotiation features), and responds to data request messages.

SAE J1939 Simulator Generates Frequently Used SAE J1939 Signals (PGNs) For Diesel Engines

Our SAE J1939 ECU Simulator Board With USB Port allows any host device (e.g., PC) with a USB COM port to monitor SAE J1939 data traffic and communicate with the SAE J1939 vehicle network, which makes it also suitable to simulate SAE J1939 data traffic. The simulation of SAE J1939 signals (i.e., PGNs) is a valuable tool for any situation from a product line test, incoming inspection, business demonstration to product development and product validation.

jCOM.J1939.USB SAE J1939 ECU Simulator Board With USB Port - Firmware Update & Hardware Upgrade

Our jCOM.J1939.USB gateway board is a high-performance, low-latency vehicle network adapter for SAE J1939 applications. It allows any host device with a USB COM port the monitoring of SAE J1939 data traffic and communication with an SAE J1939 vehicle network.