As a flavor nerd, I spend a lot of time on nuance. I consider that flavor is a constructed percept of physical and chemical exchanges between a brain and its environment. One effect of this is that there are no universal truths about flavor; attempts to experience it with any authenticity ultimately amount to individual pursuit. So, alongside my cleaning routine, I can exert physical influence by optimizing hardware combos based on temperatures that are optimized based on dosage size. I filmed some R&D for this post using IC Collective's Alley Cat—links and notes after the jump.
And, as always, these are guideposts, not traffic lights.
Low Temp
The nail: G7 Blender
The cap: 24mm quartz diamond cap
The insert: 1x 8mm quartz sphere
The temp: Hot start at 510°F
The dose: 0.07g
melt shot by anthonyjames
This blender-style nail uses 3mm tubing for thick walls in a 65mm column fed by swirled intake grooves in the dish. The resulting function is so far my ideal for low temps and small doses. The thick walls do well with holding heat, and the grooving creates enough torque to amplify how much surface the oil covers in a smooth, easy draw.
The column height accommodates a reasonable amount of draw strength, but the high torque can easily flood oil into the neck & joint. That's why I use this cap/sphere combo, rather than my ballasted cap and/or pillar. The ballasted cap can work fine, but I find it tends to pick up my oil and channel it right into the neck. To similar effect, I find my hollow pillar spatters too much up there.
Mid Temp
The nail: Victoria D
The cap: 24mm quartz diamond cap
The insert: 1x 8mm quartz sphere
The temp: Hot start at 525°F
The dose: 0.1g
melt shot by anthonyjames
This banger-style nail also uses 3mm tubing, I think (it retains heat similar to the G7), and its geometry is key. It has a short, straight band at its base (beneath the lower holes) that, together with the floor, forms most of the work surface. From there the sides slope inward up to the neck, and there is an upper drill hole angled for spin. The resulting function easily handles medium temps and a range of doses, because it tends to keep the oil down at the base, regardless of draw strength.
It takes a significant amount of draw force to pull the oil upward. With one 8mm pearl, I find it difficult to flood the neck. This thing also purrs like a kitten at high speed, which feels very satisfying! I do have the same issues with the ballasted cap as I do with the G7.
Bonus points: the sheer volume of the chamber creates enough suction that when the water backflows naturally after a draw, it exhausts noticeable puffs of vapor out the drill holes 🐲
High Temp
The nail: Titan 2
The cap: PukinBeagle Quartz Diamond Apex Cap
The insert: 1x 5x8x30mm hollow quartz pillar
The temp: Hot start at 550°F
The dose: 0.15g
melt shot by anthonyjames
This deluxe slurper-style nail uses 4mm tubing for extra thick walls in a 100mm column fed by 3 slots at the base above the dish. The resulting function is my preference for globs. The walls insulate heat so well that I often still see vapor below 400°. That is to say, it stays hot! This doesn't bode well for small dabs, so I try to stay north of .1g dosage, otherwise it's a lot like taking a shot.
The combination of chamber size and intake are what I love most about this nail. It's low torque, so to get the intended function, I've gotta pull. With the cap, which tends to resist upward air flow into the neck and is far enough away from the base to avoid channeling, I have practically no ability to flood the neck. The height of the hot column is sufficient to catch whatever the pillar throws. Taken altogether... 🚀🚀
Anya is live and ready to show you everything. Watch her strip, dance, and perform exclusive shows just for you. Interact in real-time and make your fantasies come true.
✓ Live Streaming✓ Interactive Chat✓ Private Shows✓ HD Quality✓ Free Actions
Free to watch • No registration required • HD streaming
