BigTreeTech Panda Accessories for BambuLab Printers: Guide https://3dwithus.com/bigtreetech-panda-accessories-tested-on-bambulab-printers By Will Zoobkoff StudioZombie3D
seen from Canada

seen from Estonia
seen from United States
seen from China
seen from Argentina
seen from Germany

seen from United States
seen from China

seen from India

seen from Canada

seen from Poland

seen from Malaysia

seen from Malaysia

seen from United States
seen from Belgium

seen from Austria
seen from Slovakia

seen from Slovakia
seen from Paraguay
seen from China
BigTreeTech Panda Accessories for BambuLab Printers: Guide https://3dwithus.com/bigtreetech-panda-accessories-tested-on-bambulab-printers By Will Zoobkoff StudioZombie3D

Anya is live and ready to show you everything. Watch her strip, dance, and perform exclusive shows just for you. Interact in real-time and make your fantasies come true.
Free to watch • No registration required • HD streaming
BTT SB2209 USB – Compact Toolhead Board for Klipper
The Bigtreetech SB2209 USB (RP2040) is a compact and reliable toolhead board designed for Klipper-based 3D printers, especially Voron V2.4, Trident, or custom CoreXY builds. Based on the Raspberry Pi RP2040 microcontroller, it provides powerful, low-latency communication and supports direct USB connection to the host system — ideal for setups without CAN bus.
🔧 Key Features
MCU: Raspberry Pi RP2040 dual-core processor @ 133 MHz
Connectivity: USB-C interface (no CAN bus required)
Stepper Driver: 1x TMC2209 integrated (UART mode, up to 2A RMS)
Temperature Inputs: 2x thermistor ports (100K NTC supported)
Fan Outputs:
1x controllable fan output (up to 24V, PWM)
1x always-on fan output
Heater Output: 1x hotend heater (up to 60W at 24V)
Probe Input: Dedicated input for Z probe (including inductive sensors)
Endstops: X and Y endstop inputs
LED Output: Neopixel (WS2812) port for addressable RGB LEDs
Power Input: 24V via VIN or USB only for logic
📦 Typical Use Case
Toolhead board for Voron printers using USB communication instead of CAN
Works well with Stealthburner or Clockwork 2 setups
Simplifies wiring by centralizing toolhead electronics into one board
📐 Dimensions and Mounting
Board Size: 45mm x 40mm
Mounting: Compatible with standard Stealthburner rear mounts
Cooling: Passive (no heatsink needed for typical use) shop.zen3d.eu – BTT SB2209 USB Toolhead Board
Ernie (L) has a fault on the neopixels and Bert (R) needs a fan swapping out on the Pi running octoprint but both are chugging happily away doing prototyping for @theatreinthemill tonight. #3dprinting #filamentive @filamentive #crealityender3 #crealityender5pro #bigtreetech https://www.instagram.com/p/CSxPns2M7LJ/?utm_medium=tumblr
Finally got the hot end #neopixels working. They run open white during printing for illumination but then switch to other colours to indicate printer status. Still slightly overshadowed by the bling new 80mm PSU fan and enclosure. I’m very pleased with how this worked so well on the new satsana duct. Just waiting on quiet fans arriving on the slow boat from China. #ender3 #marlinfirmware #crealityender3 #bigtreetech #skrminie3v2 https://www.instagram.com/p/CHu-WWkHfo3/?igshid=3xiumx1kpchh
My 3d printing life right now. Still trying to get this skr 1.4 turbo mobo configured. #bigtreetech #3dprintinglife #3dprinting #electronics #electricalwiring #computerhardware #cablemanagement #electroniccomponent #electronicengineering #electricalnetwork #technology #wire #electronicdevice #electricalsupply #electronicsaccessory #motherboard #circuitcomponent #hardwareprogrammer #microcontroller #computercomponent #cable #tech #electronic #instagood #photography #hack #photooftheday #device #gadget (at Ballston, Arlington, Virginia) https://www.instagram.com/p/CHnKXxKr_h4/?igshid=j1au215iqpy

Anya is live and ready to show you everything. Watch her strip, dance, and perform exclusive shows just for you. Interact in real-time and make your fantasies come true.
Free to watch • No registration required • HD streaming
Die Alpen Millionen mini mit Windows Tablet und Estcam #cncrouterprojects #cncmachining #diy #diyproject #bigtreetech #bigtreetech_skr_13 #чпу #чпустанок #чпуфрезеровка #фрезерныйстанок #фрезерныйстаноксчпу #alpenmill (hier: Oggau am Neusiedler See) https://www.instagram.com/p/CFkAF4LJHh4/?igshid=a2qzim3ydxzk
Nerve wracking few hours last night but the SKR Mini E3 v2.0 board is installed, the latest Marlin v2.0 is compiled and flashed and the BLTouch autolevelling sensor works perfectly. My Ender3 has levelled up! (As have my tinkering skills). #ender3 #bigtreetech #creality3d https://www.instagram.com/p/CFjZGojnr2W/?igshid=1wf5tlmr8ck9f