#400-101

1. Question: What standard protocol is used for port aggregation?

Answer: Standard Protocol for Port Aggregation Ten 802.3ad

2. Question: The switch has done port aggregation to connect to the computer. Can the computer be used normally?

Answer: The dynamic aggregation of the switch is connected to the computer. This interface cannot be used normally. The static aggregation does not need to be negotiated. The configuration can take effect immediately. The static aggregation configuration can be used normally after the terminal is connected.

3. Question: The aggregate interface modifies the MTU value. Does the MTU value of the physical interface change?

Answer: Modify the MTU value on the aggregation interface. The MTU value of the physical interface is still the default value.

4. Problem: Static link aggregation, one end is unplugged, and the other side is still up, causing the data not to switch to another line.

Answer: Because the middle is a photoelectric converter, the optical port is converted into multiple electrical ports, resulting in the other side not down.

5. Question: How to configure the mirror port in the case of port aggregation?

Answer: When configuring a mirrored port, if the physical interface is configured as an aggregation interface, it needs to be called in the aggregation port when mirroring.

6. Question: Is the serial number at both ends of the port aggregation the same?

Answer: The port aggregation group is locally valid, that is, the number of the two ends of the aggregation port can be different.

7. Question: Can an indirect HUB be implemented in port aggregation to achieve aggregation?

Answer: In the case of port aggregation, an indirect HUB can be aggregated. However, in order to ensure that the intermediate line is disconnected, it can be automatically detected. Dynamic link aggregation is required to detect the link.

8. Question: What is the default priority of LACP?

Answer: The LACP mode of port aggregation can be configured for priority with a default of 32768. This priority is that if the port aggregation is made on the device, the light port and the port are configured to do the aggregation together. Then, the priority determines which port pattern is made of port aggregation, the priority is configured to 0 to indicate that the interface state priority is the lowest, not to participate in the decision.

9. Question: Do Switch and Huawei switch port aggregation configuration lacp unsuccessfully?

Answer: It is recommended to use the actine mode at both ends. Otherwise, it will lead to the success of our negotiation but the data can not be forwarded properly.

10. Question: Can mirror ports be the destination interface or the source interface?

Answer: Many-to-many mirrors cannot be bidirectional and the same interface cannot be the source interface and the destination interface.

Buy Discount Cisco 400-101 Questions Is What You Need To Take

Buy Discount Cisco 400-101 Questions Is What You Need To Take

It suddenly rained. The rain in Haikou came Cisco 400-101 Questions and came, and it was a heavy rain. Now that this wish has been fulfilled, there is nothing to ask for. The blast furnace workshop. The equipment in the Cisco 400-101 Questions blast furnace workshop is broken 400-101and is being overhauled, so Cisco 400-101 Questions…

Are you really going to begin your job in IT company by passing CCIE 400-101 or already have set up for CCIE 400-101 test then you need to realize the value of having capabilities in CCIE CCIE Routing and Switching Written Exam v5.1 test. As a fresher, CCIE 400-101 prep questions will add up an appeal to your cv. How will you feel to have CCIE 400-101 exam dumps from on the internet reference with a team of Cisco experts? It noises more comforting primarily when you're by now on job.

CertificationsDesk.com | offer CCIE 400-101 new questions and training material

We provide certified alternatives for Cisco 400-101 and confirm your Establishment of center specialised skills and sets you up for CCIE 400-101 by getting 400-101 pdf dumps by CertificationsDesk.com. To help you arrive, we're producing this sort of Cisco 400-101 sample questions and CCIE 400-101 prep questions available to learners. For getting a Cisco certified you need to produce a assure to yourself and start currently.

Take our Professional's assistance online to pass Cisco 400-101 exam 

Do not only believe in us! Get an approach to Our online platform and check the success stories of our Cisco CCIE Routing and Switching Written Exam v5.1 exam professionals by getting our 400-101 questions and answers who have well prepared and cleared CCIE CCIE Routing and Switching Written Exam v5.1 test and various other exams of Cisco exams from CertificationsDesk.com. Our Cisco professional specialists have built CCIE 400-101 questions and answers with their Cisco certified knowledge thus would you be able to.You can verify their success stories online at our web page! Our CCIE 400-101 training material are created by our Cisco 400-101 certified professionals, our 400-101 dumps are made in a route with the target that representatives can without a doubt get success in just first try.

Purchase Latest Cisco 400-101 vce dumps with validated 400-101 answers

Welcome to download the newest Pass4itsure 400-101 exam

Because Cisco 400-101 exam has changed recently, Pass4itsure presents the new version of Cisco 400-101 exam practice test, which helps candidates to pass the Cisco 400-101 exam easily.The exam dumps covers all aspect of Cisco 400-101 exam.You can visit our website to free Cisco 400-101 exam download the New Version VCE Player.

QUESTION 1 Which two options are causes of out-of-order packets? (Choose two.) A. a routing loop B. a router in the packet flow path that is intermittently dropping packets C. high latency D. packets in a flow traversing multiple paths through the network E. some packets in a flow being process-switched and others being interrupt-switched on a transit router

Correct Answer: DE Explanation Explanation/Reference: In traditional packet forwarding systems, using different paths have varying latencies that cause out of order packets, eventually resulting in far lower performance for the network application. Also, if some packets are process switched quickly by the routing engine of the router while others are interrupt switched (which takes more time) then it could result in out of order packets. The other options would cause packet drops or latency, but not out of order packets.

QUESTION 2 A TCP/IP host is able to transmit small amounts of data (typically less than 1500 bytes), but attempts to transmit larger amounts of data hang and then time out. What is the cause of this problem? A. A link is flapping between two intermediate devices. B. The processor of an intermediate router is averaging 90 percent utilization. C. A port on the switch that is connected to the TCP/IP host is duplicating traffic and sending it to a port that has a sniffer attached. D. There is a PMTUD failure in the network path.

Correct Answer: D Explanation Explanation/Reference: Sometimes, over some IP paths, a TCP/IP node can send small amounts of data (typically less than 1500 bytes) with no difficulty, but transmission attempts with larger amounts of data hang, then time out. Often this is observed as a unidirectional problem in that large data transfers succeed in one direction but fail in the other direction. This problem is likely caused by the TCP MSS value, PMTUD failure, different LAN media types, or defective links.

QUESTION 3 Refer to the exhibit.

ICMP Echo requests from host A are not reaching the intended destination on host B. What is the problem? A. The ICMP payload is malformed. B. The ICMP Identifier (BE) is invalid. C. The negotiation of the connection failed. D. The packet is dropped at the next hop. E. The link is congested.

Correct Answer: D Explanation Explanation/Reference: Here we see that the Time to Live (TTL) value of the packet is one, so it will be forwarded to the next hop router, but then dropped because the TTL value will be 0 at the next hop. QUESTION 4 Refer to the exhibit.

Which statement is true? A. It is impossible for the destination interface to equal the source interface. B. NAT on a stick is performed on interface Et0/0. C. There is a potential routing loop. D. This output represents a UDP flow or a TCP flow.

Correct Answer: C Explanation Explanation/Reference: In this example we see that the source interface and destination interface are the same (Et0/0). Typically this is seen when there is a routing loop for the destination IP address. QUESTION 5 Which three conditions can cause excessive unicast flooding? (Choose three.) A. Asymmetric routing B. Repeated TCNs C. The use of HSRP D. Frames sent to FFFF.FFFF.FFFF E. MAC forwarding table overflow F. The use of Unicast Reverse Path Forwarding

Correct Answer: ABE Explanation Explanation/Reference: Causes of Flooding The very cause of flooding is that destination MAC address of the packet is not in the L2 forwarding table of the switch. In this case the packet will be flooded out of all forwarding ports in its VLAN (except the port it was received on). Below case studies display most common reasons for destination MAC address not being known to the switch. Cause 1: Asymmetric Routing Large amounts of flooded traffic might saturate low-bandwidth links causing network performance issues or complete connectivity outage to devices connected across such low-bandwidth links. Cause 2: Spanning-Tree Protocol Topology Changes Another common issue caused by flooding is Spanning-Tree Protocol (STP) Topology Change Notification (TCN). TCN is designed to correct forwarding tables after the forwarding topology has changed. This is necessary to avoid a connectivity outage, as after a topology change some destinations previously accessible via particular ports might become accessible via different ports. TCN operates by shortening the forwarding table aging time, such that if the address is not relearned, it will age out and flooding will occur. TCNs are triggered by a port that is transitioning to or from the forwarding state. After the TCN, even if the particular destination MAC address has aged out, flooding should not happen for long in most cases since the address will be relearned. The issue might arise when TCNs are occurring repeatedly with short intervals. The switches will constantly be fast-aging their forwarding tables so flooding will be nearly constant. Normally, a TCN is rare in a well-configured network. When the port on a switch goes up or down, there is eventually a TCN once the STP state of the port is changing to or from forwarding. When the port is flapping, repetitive TCNs and flooding occurs. Cause 3: Forwarding Table Overflow Another possible cause of flooding can be overflow of the switch forwarding table. In this case, new addresses cannot be learned and packets destined to such addresses are flooded until some space becomes available in the forwarding table. New addresses will then be learned. This is possible but rare, since most modern switches have large enough forwarding tables to accommodate MAC addresses for most designs. Forwarding table exhaustion can also be caused by an attack on the network where one host starts generating frames each sourced with different MAC address. This will tie up all the forwarding table resources. Once the forwarding tables become saturated, other traffic will be flooded because new learning cannot occur. This kind of attack can be detected by examining the switch forwarding table. Most of the MAC addresses will point to the same port or group of ports. Such attacks can be prevented by limiting the number of MAC addresses learned on untrusted ports by using the port security feature.

QUESTION 6 Which congestion-avoidance or congestion-management technique can cause global synchronization? A. Tail drop B. Random early detection C. Weighted random early detection D. Weighted fair queuing

Correct Answer: A Explanation Explanation/Reference: Tail Drop Tail drop treats all traffic equally and does not differentiate between classes of service. Queues fill during periods of congestion. When the output queue is full and tail drop is in effect, packets are dropped until the congestion is eliminated and the queue is no longer full. Weighted Random Early Detection WRED avoids the globalization problems that occur when tail drop is used as the congestion avoidance mechanism on the router. Global synchronization occurs as waves of congestion crest only to be followed by troughs during which the transmission link is not fully utilized. Global synchronization of TCP hosts, for example, can occur because packets are dropped all at once. Global synchronization manifests when multiple TCP hosts reduce their transmission rates in response to packet dropping, then increase their transmission rates once again when the congestion is reduced.

QUESTION 7 Which two options are reasons for TCP starvation? (Choose two.) A. The use of tail drop B. The use of WRED C. Mixing TCP and UDP traffic in the same traffic class D. The use of TCP congestion control

Correct Answer: CD Explanation Explanation/Reference: It is a general best practice to not mix TCP-based traffic with UDP-based traffic (especially Streaming-Video) within a single service-provider class because of the behaviors of these protocols during periods of congestion. Specifically, TCP transmitters throttle back flows when drops are detected. Although some UDP applications have application-level windowing, flow control, and retransmission capabilities, most UDP transmitters are completely oblivious to drops and, thus, never lower transmission rates because of dropping. When TCP flows are combined with UDP flows within a single service-provider class and the class experiences congestion, TCP flows continually lower their transmission rates, potentially giving up their bandwidth to UDP flows that are oblivious to drops. This effect is called TCP starvation/UDP dominance. TCP starvation/UDP dominance likely occurs if (TCP-based) Mission-Critical Data is assigned to the same service-provider class as (UDP-based) Streaming- Video and the class experiences sustained congestion. Even if WRED or other TCP congestion control mechanisms are enabled on the service-provider class, the same behavior would be observed because WRED (for the most part) manages congestion only on TCP-based flows.

QUESTION 8 Refer to the exhibit.

While troubleshooting high CPU utilization of a Cisco Catalyst 4500 Series Switch, you notice the error message that is shown in the exhibit in the log file. What can be the cause of this issue, and how can it be prevented? A. The hardware routing table is full. Redistribute from BGP into IGP. B. The software routing table is full. Redistribute from BGP into IGP. C. The hardware routing table is full. Reduce the number of routes in the routing table. D. The software routing table is full. Reduce the number of routes in the routing table. Correct Answer: C

Explanation Explanation/Reference: L3HWFORWADING-2 Error MessageC4K_L3HWFORWARDING-2-FWDCAMFULL:L3 routing table is full. Switching to software forwarding.

Explanation: The hardware routing table is full; forwarding takes place in the software instead. The switch performance might be degraded. Recommended Action: Reduce the size of the routing table. Enter the ip cef command to return to hardware forwarding.

QUESTION 9 Refer to the exhibit.

Which two are causes of output queue drops on FastEthernet0/0? (Choose two.) A. an oversubscribed input service policy on FastEthernet0/0 B. a duplex mismatch on FastEthernet0/0 C. a bad cable connected to FastEthernet0/0 D. an oversubscribed output service policy on FastEthernet0/0 E. The router trying to send more than 100 Mb/s out of FastEthernet0/0

Correct Answer: DE Explanation Explanation/Reference: Output drops are caused by a congested interface. For example, the traffic rate on the outgoing interface cannot accept all packets that should be sent out, or a service policy is applied that is oversubscribed. The ultimate solution to resolve the problem is to increase the line speed. However, there are ways to prevent, decrease, or control output drops when you do not want to increase the line speed. You can prevent output drops only if output drops are a consequence of short bursts of data. If output drops are caused by a constant high-rate flow, you cannot prevent the drops. However, you can control them. QUESTION 10 Refer to the exhibit.

Which statement about the output is true? A. The flow is an HTTPS connection to the router, which is initiated by 144.254.10.206. B. The flow is an HTTP connection to the router, which is initiated by 144.254.10.206. C. The flow is an HTTPS connection that is initiated by the router and that goes to 144.254.10.206. D. The flow is an HTTP connection that is initiated by the router and that goes to 144.254.10.206.

Correct Answer: A Explanation Explanation/Reference: We can see that the connection is initiated by the Source IP address shown as 144.254.10.206. We also see that the destination protocol (DstP) shows 01BB, which is in hex and translates to 443 in decimal. SSL/HTTPS uses port 443. QUESTION 11 What is the cause of ignores and overruns on an interface, when the overall traffic rate of the interface is low? A. a hardware failure of the interface B. a software bug C. a bad cable D. microbursts of traffic

Correct Answer: D Explanation Explanation/Reference: Micro-bursting is a phenomenon where rapid bursts of data packets are sent in quick succession, leading to periods of full line-rate transmission that can overflow packet buffers of the network stack, both in network endpoints and routers and switches inside the network. Symptoms of micro bursts will manifest in the form of ignores and/ or overruns (also shown as accumulated in "input error" counter within show interface output). This is indicative of receive ring and corresponding packet buffer being overwhelmed due to data bursts coming in over extremely short period of time (microseconds). You will never see a sustained data traffic within show interface's "input rate" counter as they are averaging bits per second (bps) over 5 minutes by default (way too long to account for microbursts). You can understand microbursts from a scenario where a 3-lane highway merging into a single lane at rush hour ?the capacity burst cannot exceed the total available bandwidth (i.e. single lane), but it can saturate it for a period of time.

QUESTION 12 Refer to the exhibit.

Which statement about the debug behavior of the device is true? A. The device debugs all IP events for 172.16.129.4. B. The device sends all debugging information for 172.16.129.4. C. The device sends only NTP debugging information to 172.16.129.4. D. The device sends debugging information every five seconds.

Correct Answer: A Explanation Explanation/Reference: This is an example of a conditional debug, where there is a single condition specified of IP address 172.16.129.4. So, all IP events for that address will be output in the debug. QUESTION 13 Which statement about MSS is true? A. It is negotiated between sender and receiver. B. It is sent in all TCP packets. C. It is 20 bytes lower than MTU by default. D. It is sent in SYN packets. E. It is 28 bytes lower than MTU by default.

Correct Answer: D Explanation Explanation/Reference: The maximum segment size (MSS) is a parameter of the Options field of the TCP header that specifies the largest amount of data, specified in octets, that a computer or communications device can receive in a single TCP segment. It does not count the TCP header or the IP header. The IP datagram containing a TCP segment may be self-contained within a single packet, or it may be reconstructed from several fragmented pieces; either way, the MSS limit applies to the total amount of data contained in the final, reconstructed TCP segment. The default TCP Maximum Segment Size is 536. Where a host wishes to set the maximum segment size to a value other than the default, the maximum segment size is specified as a TCP option, initially in the TCP SYN packet during the TCP handshake. The value cannot be changed after the connection is established.

QUESTION 14 Which two methods change the IP MTU value for an interface? (Choose two.) A. Configure the default MTU. B. Configure the IP system MTU. C. Configure the interface MTU. D. Configure the interface IP MTU.

Correct Answer: CD Explanation Explanation/Reference: An IOS device configured for IP+MPLS routing uses three different Maximum Transmission Unit (MTU) values: The hardware MTU configured with the mtu interface configuration command The IP MTU configured with the ip mtu interface configuration command

The MPLS MTU configured with the mpls mtu interface configuration command

The hardware MTU specifies the maximum packet length the interface can support ... or at least that's the theory behind it. In reality, longer packets can be sent (assuming the hardware interface chipset doesn't complain); therefore you can configure MPLS MTU to be larger than the interface MTU and still have a working network. Oversized packets might not be received correctly if the interface uses fixed-length buffers; platforms with scatter/gather architecture (also called particle buffers) usually survive incoming oversized packets. IP MTU is used to determine whether am IP packet forwarded through an interface has to be fragmented. It has to be lower or equal to hardware MTU (and this limitation is enforced). If it equals the HW MTU, its value does not appear in the running configuration and it tracks the changes in HW MTU. For example, if you configure ip mtu 1300 on a Serial interface, it will appear in the running configuration as long as the hardware MTU is not equal to 1300 (and will not change as the HW MTU changes). However, as soon as the mtu 1300 is configured, the ip mtu 1300 command disappears from the configuration and the IP MTU yet again tracks the HW MTU.

QUESTION 15 Which implementation can cause packet loss when the network includes asymmetric routing paths? A. the use of ECMP routing B. the use of penultimate hop popping C. the use of Unicast RPF D. disabling Cisco Express Forwarding

Correct Answer: C Explanation Explanation/Reference: When administrators use Unicast RPF in strict mode, the packet must be received on the interface that the router would use to forward the return packet. Unicast RPF configured in strict mode may drop legitimate traffic that is received on an interface that was not the router's choice for sending return traffic. Dropping this legitimate traffic could occur when asymmetric routing paths are present in the network.

QUESTION 16 Which two mechanisms can be used to eliminate Cisco Express Forwarding polarization? (Choose two.) A. alternating cost links B. the unique-ID/universal-ID algorithm C. Cisco Express Forwarding antipolarization D. different hashing inputs at each layer of the network

Correct Answer: BD Explanation Explanation/Reference: This document describes how Cisco Express Forwarding (CEF) polarization can cause suboptimal use of redundant paths to a destination network. CEF polarization is the effect when a hash algorithm chooses a particular path and the redundant paths remain completely unused. How to Avoid CEF Polarization 1. Alternate between default (SIP and DIP) and full (SIP + DIP + Layer4 ports) hashing inputs configuration at each layer of the network.

2. Alternate between an even and odd number of ECMP links at each layer of the network. The CEF load-balancing does not depend on how the protocol routes are inserted in the routing table. Therefore, the OSPF routes exhibit the same behavior as EIGRP. In a hierarchical network where there are several routers that perform load-sharing in a row, they all use same algorithm to load-share.

The hash algorithm load-balances this way by default: 1: 1 2: 7-8 3: 1-1-1 4: 1-1-1-2 5: 1-1-1-1-1 6: 1-2-2-2-2-2 7: 1-1-1-1-1-1-1 8: 1-1-1-2-2-2-2-2 The number before the colon represents the number of equal-cost paths. The number after the colon represents the proportion of traffic which is forwarded per path. This means that: For two equal cost paths, load-sharing is 46.666%-53.333%, not 50%-50%.

For three equal cost paths, load-sharing is 33.33%-33.33%-33.33% (as expected).

For four equal cost paths, load-sharing is 20%-20%-20%-40% and not 25%-25%-25%-25%.

This illustrates that, when there is even number of ECMP links, the traffic is not load-balanced. 1. Cisco IOS introduced a concept called unique-ID/universal-ID which helps avoid CEF polarization. This algorithm, called the universal algorithm (the default in current Cisco IOS versions), adds a 32-bit router-specific value to the hash function (called the universal ID - this is a randomly generated value at the time of the switch boot up that can can be manually controlled). This seeds the hash function on each router with a unique ID, which ensures that the same source/ destination pair hash into a different value on different routers along the path. This process provides a better network-wide load-sharing and circumvents the polarization issue. This unique -ID concept does not work for an even number of equal-cost paths due to a hardware limitation, but it works perfectly for an odd number of equal-cost paths. In order to overcome this problem, Cisco IOS adds one link to the hardware adjacency table when there is an even number of equal-cost paths in order to make the system believe that there is an odd number of equal-cost links.

QUESTION 17 Which two mechanisms provide Cisco IOS XE Software with control plane and data plane separation? (Choose two.) A. Forwarding and Feature Manager B. Forwarding Engine Driver C. Forwarding Performance Management D. Forwarding Information Base

Correct Answer: AB Explanation Explanation/Reference: Control Plane and Data Plane Separation IOS XE introduces an opportunity to enable teams to now build drivers for new Data Plane ASICs outside the IOS instance and have them program to a set of standard APIs which in turn enforces Control Plane and Data Plane processing separation. IOS XE accomplishes Control Plane / Data Plane separation through the introduction of the Forwarding and Feature Manager (FFM) and its standard interface to the Forwarding Engine Driver (FED). FFM provides a set of APIs to Control Plane processes. In turn, the FFM programs the Data Plane via the FED and maintains forwarding state for the system. The FED is the instantiation of the hardware driver for the Data Plane and is provided by the platform.

QUESTION 18 Refer to the exhibit.

What is the PHB class on this flow? A. EF B. none C. AF21 D. CS4

Correct Answer: D Explanation Explanation/Reference: This command shows the TOS value in hex, which is 80 in this case. The following chart shows some common DSCP/PHB Class values:

QUESTION 19 Refer to the exhibit.

What kind of load balancing is done on this router? A. per-packet load balancing B. per-flow load balancing C. per-label load balancing D. star round-robin load balancing

Correct Answer: A Explanation Explanation/Reference: Here we can see that for the same traffic source/destination pair of 10.0.0.1 to 14.0.0.2 there were a total of 100 packets (shown by second entry without the *) and that the packets were distributed evenly across the three different outgoing interfaces (34, 33, 33 packets, respectively.

Where to free download the new Cisco 400-101 exam questions to pass the exam easily? Now, Pass4itsure has publised the new version of Cisco 400-101 exam dumps with new added exam questions.you can also get free VCE and PDF, and the new Cisco 400-101 practice tests ensure your exam 100% pass. Visit Pass4itsure.com to get the 100% pass ensure!

Welcome to download the newest Pass4itsure 400-101 exam

Welcome to download the newest Flydumps Cisco 400-101 dumps

Passed with high score today for Cisco 400-101 Exam. Adobe 9A0-044 new questions will be added so I’m lucky to pass today.Almost all questions were the same includes the new question, DirectAccess, EFS, AD CS..Only used Flydumps premium vce file.

QUESTION 22 Refer to the exhibit.

Video Source S is sending interactive video traffic to Video Receiver R. Router R1 has multiple routing table entries for destination R. Which load-balancing mechanism on R1 can cause out-of-order video traffic to be received by destination R? A. per-flow load balancing on R1 for destination R B. per-source-destination pair load balancing on R1 for destination R C. CEF load balancing on R1 for destination R D. per-packet load balancing on R1 for destination R

Correct Answer: D Explanation Explanation/Reference: Per-packet load balancing guarantees equal load across all links, however potentially the packets may arrive out-of-order at the destination as differential delay may exist within the network. Reference:  QUESTION 23 What is Nagle's algorithm used for? A. To increase the latency B. To calculate the best path in distance vector routing protocols C. To calculate the best path in link state routing protocols D. To resolve issues caused by poorly implemented TCP flow control.

Correct Answer: D Explanation Explanation/Reference: Silly window syndrome is a problem in computer networking caused by poorly implemented TCP flow control. A serious problem can arise in the sliding window operation when the sending application program creates data slowly, the receiving application program consumes data slowly, or both. If a server with this problem is unable to process all incoming data, it requests that its clients reduce the amount of data they send at a time (the window setting on a TCP packet). If the server continues to be unable to process all incoming data, the window becomes smaller and smaller, sometimes to the point that the data transmitted is smaller than the packet header, making data transmission extremely inefficient. The name of this problem is due to the window size shrinking to a "silly" value. When there is no synchronization between the sender and receiver regarding capacity of the flow of data or the size of the packet, the window syndrome problem is created. When the silly window syndrome is created by the sender, Nagle's algorithm is used. Nagle's solution requires that the sender sends the first segment even if it is a small one, then that it waits until an ACK is received or a maximum sized segment (MSS) is accumulated. Reference: QUESTION 24 Which statement is true regarding the UDP checksum? A. It is used for congestion control. B. It cannot be all zeros. C. It is used by some Internet worms to hide their propagation. D. It is computed based on the IP pseudo-header.

Correct Answer: D Explanation Explanation/Reference: The method used to compute the checksum is defined in RFC 768: "Checksum is the 16-bit one's complement of the one's complement sum of a pseudo header of information from the IP header, the UDP header, and the data, padded with zero octets at the end (if necessary) to make a multiple of two octets." In other words, all 16-bit words are summed using one's complement arithmetic. Add the 16-bit values up. Each time a carry-out (17th bit) is produced, swing that bit around and add it back into the least significant bit. The sum is then one's complemented to yield the value of the UDP checksum field. If the checksum calculation results in the value zero (all 16 bits 0) it should be sent as the one's complement (all 1s).

 QUESTION 25 Which statement describes the purpose of the Payload Type field in the RTP header? A. It identifies the signaling protocol. B. It identifies the codec. C. It identifies the port numbers for RTP. D. It identifies the port numbers for RTCP.

Correct Answer: B Explanation Explanation/Reference: PT, Payload Type. 7 bits: Identifies the format of the RTP payload and determines its interpretation by the application. A profile specifies a default static mapping of payload type codes to payload formats. Additional payload type codes may be defined dynamically through non-RTP means. An RTP sender emits a single RTP payload type at any given time; this field is not intended for multiplexing separate media streams. A full list of codecs and their payload type values can be found at the link below:   QUESTION 26 Which Cisco IOS XE process administers routing and forwarding? A. Forwarding manager B. Interface manager C. Cisco IOS D. Host manager

Correct Answer: C Explanation Explanation/Reference: Some of the processes are listed in the table below:

  QUESTION 27 Which circumstance can cause packet loss due to a microburst? A. slow convergence B. a blocked spanning-tree port C. process switching D. insufficient buffers

Correct Answer: D Explanation Explanation/Reference: Micro-bursting is a phenomenon where rapid bursts of data packets are sent in quick succession, leading to periods of full line-rate transmission that can overflow packet buffers of the network stack, both in network endpoints and routers and switches inside the network. Symptoms of micro bursts will manifest in the form of ignores and/ or overruns (also shown as accumulated in "input error" counter within show interface output). This is indicative of receive ring and corresponding packet buffer being overwhelmed due to data bursts coming in over extremely short period of time (microseconds).   QUESTION 28 Which two statements about proxy ARP are true? (Choose two.) A. It is supported on networks without ARP. B. It allows machines to spoof packets. C. It must be used on a network with the host on a different subnet. D. It requires larger ARP tables. E. It reduces the amount of ARP traffic.

Correct Answer: BD Explanation Explanation/Reference: Disadvantages of Proxy ARP Hosts have no idea of the physical details of their network and assume it to be a flat network in which they can reach any destination simply by sending an ARP request. But using ARP for everything has disadvantages. These are some of the disadvantages: It increases the amount of ARP traffic on your segment.

Hosts need larger ARP tables in order to handle IP-to-MAC address mappings.

Security can be undermined. A machine can claim to be another in order to intercept packets, an act called "spoofing."

It does not work for networks that do not use ARP for address resolution.

It does not generalize to all network topologies. For example, more than one router that connects two physical networks.

  QUESTION 29 Refer to the exhibit.

Routers R1 and R2 are configured as shown, and traffic from R1 fails to reach host 209.165.201.254. Which action can you take to correct the problem? A. Ensure that R2 has a default route in its routing table. B. Change the OSPF area type on R1 and R2. C. Edit the router configurations so that address 209.165.201.254 is a routable address. D. Remove the default-information originate command from the OSPF configuration of R2. Correct Answer: A

Explanation Explanation/Reference: Not sure that any of these answers are correct, it appears that this configuration is valid for reaching that one specific host IP. Answer A does have a route to that host so it would not need a default route to get to it. Choice B is incorrect as the area types have nothing to do with this. C is incorrect as that IP address is routable, and D is needed so that R1 will have a default route advertised to it from R2 so that it can reach this destination. QUESTION 30 Which service is disabled by the no service tcp-small-servers command? A. the finger service B. the Telnet service C. the Maintenance Operation Protocol service D. the chargen service

Correct Answer: D Explanation Explanation/Reference: The TCP small servers are: Echo: Echoes back whatever you type through the telnet x.x.x.x echo command.

Chargen: Generates a stream of ASCII data. Use the telnet x.x.x.x chargen command.

DiscarD. Throws away whatever you type. Use the telnet x.x.x.x discard command.

DaytimE. Returns system date and time, if it is correct. It is correct if you run Network Time Protocol (NTP), or have set the date and time manually from the

exec level. Use the telnet x.x.x.x daytime command.   QUESTION 31 Which two Cisco Express Forwarding tables are located in the data plane? (Choose two.) A. the forwarding information base B. the label forwarding information base C. the IP routing table D. the label information table E. the adjacency table

Correct Answer: AB Explanation Explanation/Reference: The control plane runs protocols such as OSPF, BGP, STP, LDP. These protocols are needed so that routers and switches know how to forward packets and frames. The data plane is where the actual forwarding takes place. The data plane is populated based on the protocols running in the control plane. The Forwarding Information Base (FIB) is used for IP traffic and the Label FIB is used for MPLS.

QUESTION 32 Which option is the most effective action to avoid packet loss due to microbursts? A. Implement larger buffers. B. Install a faster CPU. C. Install a faster network interface. D. Configure a larger tx-ring size.

Correct Answer: A Explanation Explanation/Reference: You can't avoid or prevent them as such without modifying the sending host's application/network stack so it smoothes out the bursts. However, you can manage microbursts by tuning the size of receive buffers / rings to absorb occasional microbursts. QUESTION 33 Which two statements about packet fragmentation on an IPv6 network are true? (Choose two.) A. The fragment header is 64 bits long. B. The identification field is 32 bits long. C. The fragment header is 32 bits long. D. The identification field is 64 bits long. E. The MTU must be a minimum of 1280 bytes. F. The fragment header is 48 bits long. Correct Answer: AB Explanation

Explanation/Reference: The fragment header is shown below, being 64 bits total with a 32 bit identification field:

QUESTION 34 You are backing up a server with a 1 Gbps link and a latency of 2 ms. Which two statements about the backup are true? (Choose two.) A. The bandwidth delay product is 2 Mb. B. The default TCP send window size is the limiting factor. C. The default TCP receive window size is the limiting factor. D. The bandwidth delay product is 500 Mb. E. The bandwidth delay product is 50 Mb.

Correct Answer: AC Explanation Explanation/Reference: 1 Gbps is the same as 1000 Mbps, and 1000Mb x .0002 = 2 Mbps. With TCP based data transfers, the receive window is always the limiting factor, as the sender is generally able to send traffic at line rate, but then must wait for the acknowledgements to send more data. QUESTION 35 Which two pieces of information does RTCP use to inform endpoint devices about the RTP flow? (Choose two.) A. the transmitted octet B. the lost packet count C. session control function provisioning information D. the CNAME for session participants E. the authentication method F. MTU size changes in the path of the flow Correct Answer: AB

Explanation Explanation/Reference: RTCP transports statistics for a media connection and information such as transmitted octet and packet counts, packet loss, packet delay variation, and round-trip delay time. An application may use this information to control quality of service parameters, perhaps by limiting flow, or using a different codec.   QUESTION 36 How many hash buckets does Cisco Express Forwarding use for load balancing? A. 8 B. 16 C. 24 D. 32

Correct Answer: B Explanation Explanation/Reference: In order to understand how the load balance takes place, you must first see how the tables relate. The Cisco Express Forwarding table points to 16 hash buckets (load share table), which point to the adjacency table for parallel paths. Each packet to be switched is broken up into the source and destination address pair and checked against the loadshare table.   QUESTION 37 Which three features require Cisco Express Forwarding? (Choose three.) A. NBAR B. AutoQoS C. fragmentation D. MPLS E. UplinkFast F. BackboneFast

Correct Answer: ABD Explanation Explanation/Reference: QoS Features That Require CEF These class-based QoS features are supported only on routers that run CEF. Network Based Application Recognition (NBAR) provides intelligent network classification. For more information, refer to Network Based Application

Recognition. The AutoQoS -VoIP feature simplifies and speeds up the implementation and provisioning of QoS for VoIP traffic. This feature is enabled with the help of the

auto qos voip command. CEF must be enabled at the interface or ATM PVC before the auto qos command can be used. For more information about this feature and its prerequisites, refer to AutoQoS - VoIP. From MPLS Fundamentals - Luc De Ghein Why Is CEF Needed in MPLS Networks? Concerning MPLS, CEF is special for a certain reason; otherwise, this book would not explicitly cover it. Labeled packets that enter the router are switched according to the label forwarding information base (LFIB) on the router. IP packets that enter the router are switched according to the CEF table on the router. Regardless of whether the packet is switched according to the LFIB or the CEF table, the outgoing packet can be a labeled packet or an IP packet   QUESTION 38 Which two options are interface requirements for turbo flooding? (Choose two.) A. The interface is Ethernet. B. The interface is configured for ARPA encapsulation. C. The interface is PPP. D. The interface is configured for GRE encapsulation. E. The interface is configured for 802.1Q encapsulation.

Correct Answer: AB Explanation Explanation/Reference: In the switch, the majority of packets are forwarded in hardware; most packets do not go through the switch CPU. For those packets that do go to the CPU, you can speed up spanning tree-based UDP flooding by a factor of about four to five times by using turbo-flooding. This feature is supported over Ethernet interfaces configured for ARPA encapsulation.   QUESTION 39 Which three options are sub-subfields of the IPv4 Option Type subfield? (Choose three.) A. Option Class B. GET C. Copied D. PUSH E. Option Number F. TTL

Correct Answer: ACE Explanation Explanation/Reference: Each IP option has its own subfield format, generally structured as shown below. For most options, all three subfields are used. Option Type, Option Length and Option Data.

GOOD NEWS:Flydumps has published the new version with all the new added questions and answers.By training the Cisco 400-101 VCE dumps, you can pass the exam easily and quickly.

Welcome to download the newest Flydumps Cisco 400-101 dumps

Welcome to download the newest Dumpsoon 400-101 exam

Flydumps.com provides you with the most reliable practice exams to master Cisco 400-101 Certification. Our Microsoft questions and answers are certified by the senior lecturer and experienced technical experts in the Microsoft field. These test questions provide you with the experience of taking the Cisco 400-101 actual test.

QUESTION 1 Which two options are causes of out-of-order packets? (Choose two.) A. a routing loop B. a router in the packet flow path that is intermittently dropping packets C. high latency D. packets in a flow traversing multiple paths through the network E. some packets in a flow being process-switched and others being interrupt-switched on a transit router

Correct Answer: DE Explanation Explanation/Reference: In traditional packet forwarding systems, using different paths have varying latencies that cause out of order packets, eventually resulting in far lower performance for the network application. Also, if some packets are process switched quickly by the routing engine of the router while others are interrupt switched (which takes more time) then it could result in out of order packets. The other options would cause packet drops or latency, but not out of order packets.

QUESTION 2 A TCP/IP host is able to transmit small amounts of data (typically less than 1500 bytes), but attempts to transmit larger amounts of data hang and then time out. What is the cause of this problem? A. A link is flapping between two intermediate devices. B. The processor of an intermediate router is averaging 90 percent utilization. C. A port on the switch that is connected to the TCP/IP host is duplicating traffic and sending it to a port that has a sniffer attached. D. There is a PMTUD failure in the network path.

Correct Answer: D Explanation Explanation/Reference: Sometimes, over some IP paths, a TCP/IP node can send small amounts of data (typically less than 1500 bytes) with no difficulty, but transmission attempts with larger amounts of data hang, then time out. Often this is observed as a unidirectional problem in that large data transfers succeed in one direction but fail in the other direction. This problem is likely caused by the TCP MSS value, PMTUD failure, different LAN media types, or defective links. Reference:   QUESTION 3 Refer to the exhibit.

ICMP Echo requests from host A are not reaching the intended destination on host B. What is the problem? A. The ICMP payload is malformed. B. The ICMP Identifier (BE) is invalid. C. The negotiation of the connection failed. D. The packet is dropped at the next hop. E. The link is congested.

Correct Answer: D Explanation Explanation/Reference: Here we see that the Time to Live (TTL) value of the packet is one, so it will be forwarded to the next hop router, but then dropped because the TTL value will be 0 at the next hop. QUESTION 4 Refer to the exhibit.

Which statement is true? A. It is impossible for the destination interface to equal the source interface. B. NAT on a stick is performed on interface Et0/0. C. There is a potential routing loop. D. This output represents a UDP flow or a TCP flow.

Correct Answer: C Explanation Explanation/Reference: In this example we see that the source interface and destination interface are the same (Et0/0). Typically this is seen when there is a routing loop for the destination IP address. QUESTION 5 Which three conditions can cause excessive unicast flooding? (Choose three.) A. Asymmetric routing B. Repeated TCNs C. The use of HSRP D. Frames sent to FFFF.FFFF.FFFF E. MAC forwarding table overflow F. The use of Unicast Reverse Path Forwarding

Correct Answer: ABE Explanation Explanation/Reference: Causes of Flooding The very cause of flooding is that destination MAC address of the packet is not in the L2 forwarding table of the switch. In this case the packet will be flooded out of all forwarding ports in its VLAN (except the port it was received on). Below case studies display most common reasons for destination MAC address not being known to the switch. Cause 1: Asymmetric Routing Large amounts of flooded traffic might saturate low-bandwidth links causing network performance issues or complete connectivity outage to devices connected across such low-bandwidth links. Cause 2: Spanning-Tree Protocol Topology Changes Another common issue caused by flooding is Spanning-Tree Protocol (STP) Topology Change Notification (TCN). TCN is designed to correct forwarding tables after the forwarding topology has changed. This is necessary to avoid a connectivity outage, as after a topology change some destinations previously accessible via particular ports might become accessible via different ports. TCN operates by shortening the forwarding table aging time, such that if the address is not relearned, it will age out and flooding will occur. TCNs are triggered by a port that is transitioning to or from the forwarding state. After the TCN, even if the particular destination MAC address has aged out, flooding should not happen for long in most cases since the address will be relearned. The issue might arise when TCNs are occurring repeatedly with short intervals. The switches will constantly be fast-aging their forwarding tables so flooding will be nearly constant. Normally, a TCN is rare in a well-configured network. When the port on a switch goes up or down, there is eventually a TCN once the STP state of the port is changing to or from forwarding. When the port is flapping, repetitive TCNs and flooding occurs. Cause 3: Forwarding Table Overflow Another possible cause of flooding can be overflow of the switch forwarding table. In this case, new addresses cannot be learned and packets destined to such addresses are flooded until some space becomes available in the forwarding table. New addresses will then be learned. This is possible but rare, since most modern switches have large enough forwarding tables to accommodate MAC addresses for most designs. Forwarding table exhaustion can also be caused by an attack on the network where one host starts generating frames each sourced with different MAC address. This will tie up all the forwarding table resources. Once the forwarding tables become saturated, other traffic will be flooded because new learning cannot occur. This kind of attack can be detected by examining the switch forwarding table. Most of the MAC addresses will point to the same port or group of ports. Such attacks can be prevented by limiting the number of MAC addresses learned on untrusted ports by using the port security feature. QUESTION 6 Which congestion-avoidance or congestion-management technique can cause global synchronization? A. Tail drop B. Random early detection C. Weighted random early detection D. Weighted fair queuing

Correct Answer: A Explanation Explanation/Reference: Tail Drop Tail drop treats all traffic equally and does not differentiate between classes of service. Queues fill during periods of congestion. When the output queue is full and tail drop is in effect, packets are dropped until the congestion is eliminated and the queue is no longer full. Weighted Random Early Detection WRED avoids the globalization problems that occur when tail drop is used as the congestion avoidance mechanism on the router. Global synchronization occurs as waves of congestion crest only to be followed by troughs during which the transmission link is not fully utilized. Global synchronization of TCP hosts, for example, can occur because packets are dropped all at once. Global synchronization manifests when multiple TCP hosts reduce their transmission rates in response to packet dropping, then increase their transmission rates once again when the congestion is reduced. Reference:  QUESTION 7 Which two options are reasons for TCP starvation? (Choose two.) A. The use of tail drop B. The use of WRED C. Mixing TCP and UDP traffic in the same traffic class D. The use of TCP congestion control

Correct Answer: CD Explanation Explanation/Reference: It is a general best practice to not mix TCP-based traffic with UDP-based traffic (especially Streaming-Video) within a single service-provider class because of the behaviors of these protocols during periods of congestion. Specifically, TCP transmitters throttle back flows when drops are detected. Although some UDP applications have application-level windowing, flow control, and retransmission capabilities, most UDP transmitters are completely oblivious to drops and, thus, never lower transmission rates because of dropping. When TCP flows are combined with UDP flows within a single service-provider class and the class experiences congestion, TCP flows continually lower their transmission rates, potentially giving up their bandwidth to UDP flows that are oblivious to drops. This effect is called TCP starvation/UDP dominance. TCP starvation/UDP dominance likely occurs if (TCP-based) Mission-Critical Data is assigned to the same service-provider class as (UDP-based) Streaming- Video and the class experiences sustained congestion. Even if WRED or other TCP congestion control mechanisms are enabled on the service-provider class, the same behavior would be observed because WRED (for the most part) manages congestion only on TCP-based flows. Reference:   QUESTION 8 Refer to the exhibit.

While troubleshooting high CPU utilization of a Cisco Catalyst 4500 Series Switch, you notice the error message that is shown in the exhibit in the log file. What can be the cause of this issue, and how can it be prevented? A. The hardware routing table is full. Redistribute from BGP into IGP. B. The software routing table is full. Redistribute from BGP into IGP. C. The hardware routing table is full. Reduce the number of routes in the routing table. D. The software routing table is full. Reduce the number of routes in the routing table. Correct Answer: C

Explanation Explanation/Reference: L3HWFORWADING-2 Error MessageC4K_L3HWFORWARDING-2-FWDCAMFULL:L3 routing table is full. Switching to software forwarding.

Explanation: The hardware routing table is full; forwarding takes place in the software instead. The switch performance might be degraded. Recommended Action: Reduce the size of the routing table. Enter the ip cef command to return to hardware forwarding.

QUESTION 9 Refer to the exhibit.

Which two are causes of output queue drops on FastEthernet0/0? (Choose two.) A. an oversubscribed input service policy on FastEthernet0/0 B. a duplex mismatch on FastEthernet0/0 C. a bad cable connected to FastEthernet0/0 D. an oversubscribed output service policy on FastEthernet0/0 E. The router trying to send more than 100 Mb/s out of FastEthernet0/0

Correct Answer: DE Explanation Explanation/Reference: Output drops are caused by a congested interface. For example, the traffic rate on the outgoing interface cannot accept all packets that should be sent out, or a service policy is applied that is oversubscribed. The ultimate solution to resolve the problem is to increase the line speed. However, there are ways to prevent, decrease, or control output drops when you do not want to increase the line speed. You can prevent output drops only if output drops are a consequence of short bursts of data. If output drops are caused by a constant high-rate flow, you cannot prevent the drops. However, you can control them. Reference:  QUESTION 10 Refer to the exhibit.

Which statement about the output is true? A. The flow is an HTTPS connection to the router, which is initiated by 144.254.10.206. B. The flow is an HTTP connection to the router, which is initiated by 144.254.10.206. C. The flow is an HTTPS connection that is initiated by the router and that goes to 144.254.10.206. D. The flow is an HTTP connection that is initiated by the router and that goes to 144.254.10.206.

Correct Answer: A Explanation Explanation/Reference: We can see that the connection is initiated by the Source IP address shown as 144.254.10.206. We also see that the destination protocol (DstP) shows 01BB, which is in hex and translates to 443 in decimal. SSL/HTTPS uses port 443. QUESTION 11 What is the cause of ignores and overruns on an interface, when the overall traffic rate of the interface is low? A. a hardware failure of the interface B. a software bug C. a bad cable D. microbursts of traffic

Correct Answer: D Explanation Explanation/Reference: Micro-bursting is a phenomenon where rapid bursts of data packets are sent in quick succession, leading to periods of full line-rate transmission that can overflow packet buffers of the network stack, both in network endpoints and routers and switches inside the network. Symptoms of micro bursts will manifest in the form of ignores and/ or overruns (also shown as accumulated in "input error" counter within show interface output). This is indicative of receive ring and corresponding packet buffer being overwhelmed due to data bursts coming in over extremely short period of time (microseconds). You will never see a sustained data traffic within show interface's "input rate" counter as they are averaging bits per second (bps) over 5 minutes by default (way too long to account for microbursts). You can understand microbursts from a scenario where a 3-lane highway merging into a single lane at rush hour ?the capacity burst cannot exceed the total available bandwidth (i.e. single lane), but it can saturate it for a period of time. QUESTION 12 Refer to the exhibit.

Which statement about the debug behavior of the device is true? A. The device debugs all IP events for 172.16.129.4. B. The device sends all debugging information for 172.16.129.4. C. The device sends only NTP debugging information to 172.16.129.4. D. The device sends debugging information every five seconds.

Correct Answer: A Explanation Explanation/Reference: This is an example of a conditional debug, where there is a single condition specified of IP address 172.16.129.4. So, all IP events for that address will be output in the debug. QUESTION 13 Which statement about MSS is true? A. It is negotiated between sender and receiver. B. It is sent in all TCP packets. C. It is 20 bytes lower than MTU by default. D. It is sent in SYN packets. E. It is 28 bytes lower than MTU by default.

Correct Answer: D Explanation Explanation/Reference: The maximum segment size (MSS) is a parameter of the Options field of the TCP header that specifies the largest amount of data, specified in octets, that a computer or communications device can receive in a single TCP segment. It does not count the TCP header or the IP header. The IP datagram containing a TCP segment may be self-contained within a single packet, or it may be reconstructed from several fragmented pieces; either way, the MSS limit applies to the total amount of data contained in the final, reconstructed TCP segment. The default TCP Maximum Segment Size is 536. Where a host wishes to set the maximum segment size to a value other than the default, the maximum segment size is specified as a TCP option, initially in the TCP SYN packet during the TCP handshake. The value cannot be changed after the connection is established. QUESTION 14 Which two methods change the IP MTU value for an interface? (Choose two.) A. Configure the default MTU. B. Configure the IP system MTU. C. Configure the interface MTU. D. Configure the interface IP MTU.

Correct Answer: CD Explanation Explanation/Reference: An IOS device configured for IP+MPLS routing uses three different Maximum Transmission Unit (MTU) values: The hardware MTU configured with the mtu interface configuration command The IP MTU configured with the ip mtu interface configuration command

The MPLS MTU configured with the mpls mtu interface configuration command

The hardware MTU specifies the maximum packet length the interface can support ... or at least that's the theory behind it. In reality, longer packets can be sent (assuming the hardware interface chipset doesn't complain); therefore you can configure MPLS MTU to be larger than the interface MTU and still have a working network. Oversized packets might not be received correctly if the interface uses fixed-length buffers; platforms with scatter/gather architecture (also called particle buffers) usually survive incoming oversized packets. IP MTU is used to determine whether am IP packet forwarded through an interface has to be fragmented. It has to be lower or equal to hardware MTU (and this limitation is enforced). If it equals the HW MTU, its value does not appear in the running configuration and it tracks the changes in HW MTU. For example, if you configure ip mtu 1300 on a Serial interface, it will appear in the running configuration as long as the hardware MTU is not equal to 1300 (and will not change as the HW MTU changes). However, as soon as the mtu 1300 is configured, the ip mtu 1300 command disappears from the configuration and the IP MTU yet again tracks the HW MTU. Reference:   QUESTION 15 Which implementation can cause packet loss when the network includes asymmetric routing paths? A. the use of ECMP routing B. the use of penultimate hop popping C. the use of Unicast RPF D. disabling Cisco Express Forwarding

Correct Answer: C Explanation Explanation/Reference: When administrators use Unicast RPF in strict mode, the packet must be received on the interface that the router would use to forward the return packet. Unicast RPF configured in strict mode may drop legitimate traffic that is received on an interface that was not the router's choice for sending return traffic. Dropping this legitimate traffic could occur when asymmetric routing paths are present in the network. QUESTION 16 Which two mechanisms can be used to eliminate Cisco Express Forwarding polarization? (Choose two.) A. alternating cost links B. the unique-ID/universal-ID algorithm C. Cisco Express Forwarding antipolarization D. different hashing inputs at each layer of the network

Correct Answer: BD Explanation Explanation/Reference: This document describes how Cisco Express Forwarding (CEF) polarization can cause suboptimal use of redundant paths to a destination network. CEF polarization is the effect when a hash algorithm chooses a particular path and the redundant paths remain completely unused. How to Avoid CEF Polarization 1. Alternate between default (SIP and DIP) and full (SIP + DIP + Layer4 ports) hashing inputs configuration at each layer of the network.

2. Alternate between an even and odd number of ECMP links at each layer of the network. The CEF load-balancing does not depend on how the protocol routes are inserted in the routing table. Therefore, the OSPF routes exhibit the same behavior as EIGRP. In a hierarchical network where there are several routers that perform load-sharing in a row, they all use same algorithm to load-share.

The hash algorithm load-balances this way by default: 1: 1 2: 7-8 3: 1-1-1 4: 1-1-1-2 5: 1-1-1-1-1 6: 1-2-2-2-2-2 7: 1-1-1-1-1-1-1 8: 1-1-1-2-2-2-2-2 The number before the colon represents the number of equal-cost paths. The number after the colon represents the proportion of traffic which is forwarded per path. This means that: For two equal cost paths, load-sharing is 46.666%-53.333%, not 50%-50%.

For three equal cost paths, load-sharing is 33.33%-33.33%-33.33% (as expected).

For four equal cost paths, load-sharing is 20%-20%-20%-40% and not 25%-25%-25%-25%.

This illustrates that, when there is even number of ECMP links, the traffic is not load-balanced. 1. Cisco IOS introduced a concept called unique-ID/universal-ID which helps avoid CEF polarization. This algorithm, called the universal algorithm (the default in current Cisco IOS versions), adds a 32-bit router-specific value to the hash function (called the universal ID - this is a randomly generated value at the time of the switch boot up that can can be manually controlled). This seeds the hash function on each router with a unique ID, which ensures that the same source/ destination pair hash into a different value on different routers along the path. This process provides a better network-wide load-sharing and circumvents the polarization issue. This unique -ID concept does not work for an even number of equal-cost paths due to a hardware limitation, but it works perfectly for an odd number of equal-cost paths. In order to overcome this problem, Cisco IOS adds one link to the hardware adjacency table when there is an even number of equal-cost paths in order to make the system believe that there is an odd number of equal-cost links. QUESTION 17 Which two mechanisms provide Cisco IOS XE Software with control plane and data plane separation? (Choose two.) A. Forwarding and Feature Manager B. Forwarding Engine Driver C. Forwarding Performance Management D. Forwarding Information Base

Correct Answer: AB Explanation Explanation/Reference: Control Plane and Data Plane Separation IOS XE introduces an opportunity to enable teams to now build drivers for new Data Plane ASICs outside the IOS instance and have them program to a set of standard APIs which in turn enforces Control Plane and Data Plane processing separation. IOS XE accomplishes Control Plane / Data Plane separation through the introduction of the Forwarding and Feature Manager (FFM) and its standard interface to the Forwarding Engine Driver (FED). FFM provides a set of APIs to Control Plane processes. In turn, the FFM programs the Data Plane via the FED and maintains forwarding state for the system. The FED is the instantiation of the hardware driver for the Data Plane and is provided by the platform. Reference: ://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-xe-3sg/QA_C67-622903.html QUESTION 18 Refer to the exhibit.

What is the PHB class on this flow? A. EF B. none C. AF21 D. CS4

Correct Answer: D Explanation Explanation/Reference: This command shows the TOS value in hex, which is 80 in this case. The following chart shows some common DSCP/PHB Class values:

  QUESTION 19 Refer to the exhibit.

What kind of load balancing is done on this router? A. per-packet load balancing B. per-flow load balancing C. per-label load balancing D. star round-robin load balancing

Correct Answer: A Explanation Explanation/Reference: Here we can see that for the same traffic source/destination pair of 10.0.0.1 to 14.0.0.2 there were a total of 100 packets (shown by second entry without the *) and that the packets were distributed evenly across the three different outgoing interfaces (34, 33, 33 packets, respectively. QUESTION 20 What is the most efficient way to confirm whether microbursts of traffic are occurring? A. Monitor the output traffic rate using the show interface command. B. Monitor the output traffic rate using the show controllers command. C. Check the CPU utilization of the router. D. Sniff the traffic and plot the packet rate over time.

Correct Answer: D Explanation Explanation/Reference: Micro-bursting is a phenomenon where rapid bursts of data packets are sent in quick succession, leading to periods of full line-rate transmission that can overflow packet buffers of the network stack, both in network endpoints and routers and switches inside the network. In order to troubleshoot microbursts, you need a packet sniffer that can capture traffic over a long period of time and allow you to analyze it in the form of a graph which displays the saturation points (packet rate during microbursts versus total available bandwidth). You can eventually trace it to the source causing the bursts (e.g. stock trading applications). Reference: Adam, Paul (2014-07-12). All-in-One CCIE V5 Written Exam Guide (Kindle Locations 989-994). Kindle Edition. QUESTION 21 What is a cause for unicast flooding? A. Unicast flooding occurs when multicast traffic arrives on a Layer 2 switch that has directly connected multicast receivers. B. When PIM snooping is not enabled, unicast flooding occurs on the switch that interconnects the PIM-enabled routers. C. A man-in-the-middle attack can cause the ARP cache of an end host to have the wrong MAC address. Instead of having the MAC address of the default gateway, it has a MAC address of the man-in-the-middle. This causes all traffic to be unicast flooded through the man-in-the-middle, which can then sniff all packets. D. Forwarding table overflow prevents new MAC addresses from being learned, and packets destined to those MAC addresses are flooded until space becomes available in the forwarding table.

Correct Answer: D

Flydumps.com takes in the latest Cisco 400-101 questions in the Cisco 400-101 exam materials so that our material should be always the latest and the most relevant. We know that Cisco 400-101 examination  wouldn’t repeat the same set of questions all the time. Microsoft certification examinations are stringent and focus is often kept on updated technology trends. The Cisco 400-101 exam questions organized by the professionals will help to condition your mind to promptly grasp what you could be facing in the Cisco 400-101 cert examination.

Welcome to download the newest Dumpsoon 400-101 exam:  

NO.1 Which three services does Cisco provide to customers.? (Choose three.) A. Cisco focuses solely on the cloud and web-based offerings, enabling endpoints to communicate. B. Cisco accelerates the ability of IT to align more closely with the business and how people actually work. C. Cisco delivers deployment agility across endpoints and the network, including the cloud, whether on premises or off premises. D. Cisco focuses mainly on devices linking endpoints and applications via a common framework. E. Cisco delivers borderless experience across all major devices and operating systems. Answer: B,C,E Cisco answers real questions   646-206   646-206 study guide   646-206 NO.2 What are three current business factors that are influencing customer decisions in making technology investments? (Choose three.) A. return on investment B. competitiveness C. number of product features D. day one costs E. regulation F. availability of budget Answer: A,B,E Cisco Study Guide   646-206 Test Answers   646-206   646-206 Exam Dumps   646-206 NO.3 Which three Cisco go-to-market strategies help partner profitability? (Choose three.) A. Cisco innovation and acquisitions ensure that partners have a broad portfolio for customers. B. Cisco has one partner program to support all partner types. C. Cisco focuses on meeting customer needs while protecting partner profitability. D. Cisco focuses only on building internally for innovation and not on acquisitions. E. Cisco provides partner programs to support different partner business models. Answer: A,C,E Cisco braindump   646-206   646-206 dumps   646-206 NO.4 In which area of the campus LAN are the user computers attached to the network? A. core B. access C. distribution D. aggregation Answer: B Cisco Training online   646-206 exam   646-206   646-206 NO.5 Which three customer needs are addressed by Cisco solutions? (Choose three.) A. reducing day one costs B. improving productivity C. gaining competitive advantage D. focusing on current needs E. obtaining a wide variety of point products F. reducing TCO Answer: B,C,F Cisco Practice Test   646-206 pdf   646-206 Braindumps   646-206 exam prep   646-206 Study Guide NO.6 You discover that a financial institution is planning to acquire two banks and wants to scale its infrastructure independent of the size of the acquired entities and deliver next-generation functionality almost immediately. Which three options are the most appropriate questions to ask a business decision maker? (Choose three.) A. What are your plans for expanding services and offerings to your customers and your staff? B. What issues are you experiencing related to technical readiness, implementation, monitoring, and optimization? C. How are growing costs affecting the flexibility of your company and its profit margin? D. How quickly can your IT staff roll out new applications? E. What do you see as the greatest risks to your business? F. What technical issues concern you the most? Answer: A,C,E Cisco PDF VCE   646-206 Free download   646-206 Test Answers   646-206 dumps torrent   646-206 Exam Prep   646-206 Exam Questions NO.7 Which option best describes the primary value of the Cisco IP Next-Generation Network? A. interoperates seamlessly with customers, though with only a few applications B. provides unique network intelligence that runs throughout the architecture, regardless of traffic mix or device C. embeds intelligence in the core only D. provides an access-specific solution that targets optical and Ethernet products E. integrates only two of the four Cisco architectures Answer: B Cisco Exam Tests   646-206 exam   646-206   646-206   646-206 Dumps PDF NO.8 What is the Cisco goal regarding market share for each of the major markets that its products compete in? A. to compete effectively in every market in which Cisco participates B. to be No.1 or No. 2 in every market in which Cisco participates C. to be in the top 1 percent in every market in which Cisco participates D. to be first in every market in which Cisco participates Answer: B Cisco Exam Tests   646-206 Training online   646-206 Exam Cost

ITCertMaster could give you the Cisco 400-101 exam questions and answers that with the highest quality. With the material you can successed step by step. ITCertMaster's Cisco 400-101 exam training materials are absolutely give you a true environment of the test preparation. Our material is highly targeted, just as tailor-made for you. With it you will become a powerful IT experts. ITCertMaster's Cisco 400-101 exam training materials will be most suitable for you. Quickly registered ITCertMaster website please, I believe that you will have a windfall.

You can now get Cisco 646-206 exam certification our ITCertMaster have the full version of Cisco 646-206 exam. You do not need to look around for the latest Cisco 646-206 training materials, because you have to find the best Cisco 646-206 training materials. Rest assured that our questions and answers, you will be completely ready for the Cisco 646-206 certification exam.

ITCertMaster provides a clear and superior solutions for each Cisco 400-101 exam candidates. We provide you with the Cisco 400-101 exam questions and answers. Our team of IT experts is the most experienced and qualified. Our test questions and the answer is almost like the real exam. This is really amazing. More importantly, the examination pass rate of ITCertMaster is highest in the worldwide.

Exam Code: 400-101 Exam Name: CCIE Routing and Switching Written Exam v5.0 Guaranteed success with practice guides, No help, Full refund! Cisco 400-101 Latest Dumps 650 Q&As Updated: 07-20,2015 400-101 Study Guide Detail : 400-101 Latest Dumps

Exam Code: 646-206 Exam Name: Cisco Sales Expert Guaranteed success with practice guides, No help, Full refund! Cisco 646-206 Exam Cost 60 Q&As Updated: 07-20,2015 646-206 Test Questions Detail : 646-206 Exam Cost

If you buy ITCertMaster Cisco 400-101 exam training materials, you will solve the problem of your test preparation. You will get the training materials which have the highest quality. Buy our products today, and you will open a new door, and you will get a better future. We can make you pay a minimum of effort to get the greatest success.

Only to find a way to success, not to make excuses for failure. ITCertMaster's 400-101 exam certification training materials include 400-101 exam dumps and answers. The data is worked out by our experienced team of IT professionals with their own exploration and continuous practice. ITCertMaster's 400-101 exam certification training materials have high accuracy and wide coverage. It will be a grand helper that will accompany you to prepare for 400-101 certification exam.