New Post has been published on https://coolcarsnews.com/one-of-a-kind/
A Wildly Customized 1938 Cummins Swapped Avoid
Nate Wilson, of Grass Valley, Ca, wanted something different. In the last couple of years Nate has become a well-known vehicle and truck builder within Northern California, and has constructed everything from twin turbo Chevelles, to Coyote-swapped Broncos. Vehicles own a special place in their heart though, as do petrol. āI found a 1938 Dodge and I knew this just needed a Cummins in it, ā fun Nate.
Why is Nateās ride especially special, is that itās not an entire body swap. A lot of swaps simply use an existing chassis, state a ā94 Dodge Ram dually, and exchange and old timey entire body on top. Nate decided to go the particular much harder route associated with using the factory ā38 framework, and build the rest of the framework to match the ideas which were inside his head. Even though it doesnāt look like any tow line truck weāve seen, this technically is one. Nate constructed the entire rear frame from mammoth 2 by 10-inch boxed square tubing, and after that topped it off having a custom flatbed. The 16-foot bed was just the start of build though, and with the assist of good fabrication buddy Zachary Hite, there was a lot more ahead.
The 5. 9L Cummins 12v is share, save for a few minor enhancements. Some timing has been put into the engine, as well as a FASS 150 lift water pump, governor springs, and valvesprings that enable the motor to rev past 3 or more, 000 rpm before the shift. Power is approximated at 300hp at the flywheel, and around 700lb-ft torque capacity.
Given that Nate practically needs a 4by4 to get down the miles-long grime road that leads to their house, building a 2-wd pickup truck just wasnāt on the menus. After the chassis was constructed, next came the front plus rear suspension, which were custom-made by Nate. Up front, a good ā09 Ford front side axle was incorporated to the boxed ā38 frame, plus hung with a tweaked WFO kit with King 2 . 5 coil-over shocks and dual guiding stabilizers. The rear suspension is how things got wild, being a four-bag Firestone air flow system has been modified simply by Nate into a parallel four-link arrangement. The incredibly strong rear suspension and Dana 80 axle cannot only handle the weight from the 8, 000-pound Dodge , yet a 10, 000-pound truck along with the flatbed as well.
Nate went with a more recent generation HY35 turbocharger, which usually spools even quicker compared to stock HX35. He furthermore externally wastegated it on 30psi so it could reside a long and happy living.
Nate was making good improvement with his truck, and definitely, he was building a creature. With the truck being the particular behemoth that it is, there was simply no powerplant that would do apart from a diesel. The diesel powered that powers the Avoid is a legendary Cummins 12-valve, that was pulled out of a ā97 Dodge. Before it was set up Nate hopped it up a bit to the tune of about 300hp and 700lb-ft, and improved the engineās rpm variety so that he could wind away the gears a bit using the manual transmission. Speaking of guides, the 5. 9L motor is backed by a NV4500 transmission and Ford 205 transfer case, which provides each stump pulling power plus freeway cruisinā. Fitting the particular diesel engine into the ā38 was no easy job. The firewall had to be indented, and both a customized radiator and Mishimoto intercooler had to be installed to be able to tuck into the narrow front side grille. Nate somehow caused it to be all work, but even while we were taking photos it had been hard to believe he match it all in there.
The 4-inch downpipe exits the particular turbocharger and is routed right into a giant 10-inch stack, that provides the ā38 a serious mellow tone.
When taking Nateās creation in, it becomes obvious that his crazy focus on detail on the undercarriage is probably the most impressive aspect of the particular Dodge. Thereās a whole various other build underneath the truck, because thatās where Nate meticulously hid 40 gallons really worth of air tanks, 2 compressors, two batteries, along with a train horn. Wherever possible Nate used vintage parts, from your train horn off of a real train, to the ā50s firetruck siren mounted on a ā53 Mercury Monterey bumper. The particular paint of course is the Nature styled original patina that can be clear coated, and in some way works just perfect with the chrome. Yes, from the auto tires to the tip of the collection, we can definitely say Nateās ā38 is one of a type.
The front stack within Nateās Dodge is a quite interesting arrangement. He got the dimensions, and then almost everything was built to suit. The particular radiator was a custom offer out of Service Center Radiator in Auburn, Ca, and the Mishimoto intercooler was obviously an universal piece based upon their power goals.
The bottom front of the vehicle is just as detailed as any various other part. Here you can see underneath of the Cummins engine plus NV4500, as well as the front hyperlink suspension arrangement.
The killer chrome tires on the ā38 are quite the particular conversation piece. The twenty two. 5-inch Alcoas which have been cut down to 22 ins by Michaelās Truck Functions in Mesa, Arizona, plus fitted with āWilsonz Kustomzā billet centercaps to promote Nateās shop.
Nate needed a beefy rearend to handle the weight of the vehicle, as well as any load he may be carrying. Ā The Dana 80 rearend along with 3. 73 gears had been selected for the job, plus was further upgraded using a locker from Yukon Gear .
Thereās an entire second vehicleās worth associated with work underneath the truck. The whole 26-foot frame has been powder-coated Misty Rootbeer, the air compressors, tanks, and batteries are mounted along the frame, as well as the rear suspension is a complete custom parallel 4-link set up that uses Firestone safetybags. Thereās also train horns, and a custom driveline through Drive line Services within Sacramento, California.
There was no way Nate would definitely be rolling down the road on 80-year-old Dodge suspension system. The front framerails were encased, and King 2 . 5-inch coil-over shocks and a good ā09 Ford Super Responsibility axle with dual guiding stabilizers gave Nate a good platform to build upon.
The front suspension is founded on a solid axle conversion package from WFO , which Nate has seamlessly integrated into the particular Dodge.
Having a host of gauges, the tilt steering column, plus an original dash, the interior is definitely an interesting mixture of old plus new.
Nate laughed when we asked in which he found a seat that will fit so perfectly. Simply no itās not a Dodge chair, itās out of a Chevy S10 pickup!
Nate needs to be capable of use his Dodge to get future projects whether they operate or not, so he installed a heavy-duty 12, 000-pound Alert winch for the front of the bed, directly behind the cab.
By using the air suspension Nate is able to drop his flatbed almost all the way to the ground. Meant for lower cars he also offers a set of ramps that assist āem onto the porch.
Virtually all of the cab plus front of the body is nevertheless factory original. Even the double-hinged engine still works correctly.
Perhaps one of the more fascinating parts on the truck could be the huge front bumper that will had us guessing. It is actually not off of the pickup, but was pirated from the 1953 Mercury Monterey.
The front grille from the Dodge is factory, yet has been jazzed up with the and new theme. The siren from the ā50s can be mounted on the front bumper, together with newer LED headlight light.
<! -- AddThis Advanced Settings generic through filter on the_content <! -- AddThis Share Buttons generic through filter on the_content
