Untitled

𝐵𝑒𝓈𝓅𝑜𝓀𝑒 𝒪𝒶𝓀 𝐸𝒶𝓈𝑒𝓁 𝒫𝒾𝒸𝓉𝓊𝓇𝑒 𝒮𝓉𝒶𝓃𝒹 This was a long time in the making, not because it took me a long time to make, but because i had to wait a long time for the oak due all that has been going on in the last few months. - I was asked by a really lovely cornish lady, if i could make an easel picture stand suitable for a one off resin & ply picture. - Air dried oak was my timber of choice, i wanted to make it a little different to the ‘normal’ easels you see, so shaped the legs and came up with an idea for the hinge and to also to not have a chain or string to keep the legs from opening any further than needed. - I used a brass counter flap hinge,sourced from Ironmongerydirect, set in on the underside, which although not immediately visible, looks nice i think & provides a strong hinge point. I set the hinge in a bit lower down, shaped and angled the tops of the legs so that when opened, the top sections meet and thus cannot open any further. This posed a couple of headaches! One was working out the angles for it to all work, the second was to get it all together and to get the screws in! With the hinge on the underside i had to be mindful of how far the legs needed to open as well as having just enough clearance to get the screws in! I did say ‘just enough’ 😂 - All assembled, two coats of oil and delivered with the picture in place, i am really happy how it turned out! 😁 #oak #oakeasel #bespokeoak #bespokeoakeasel #oakeasel #oakpicturestand #picture #resinpicture #resinpicturestand #picturestand #cornwall #kernow #carpentry #woodwork #woodworking (at Cornwall) https://www.instagram.com/p/CBGGw8wj0jx/?igshid=1k2y33nliao3v

𝓢𝓬𝓻𝓮𝔀𝓼! I wanted to share this post, it is not sponsored or endorsed , just what i did, why i did it, and my own opinions! - Today i carried out a little repair to one of my garden gates, it had come under a bot of abuse from the kids and wind damage. - What was going to be a quick job refixing two of the pickets, turned into replacing all the screws! - Now i only threw these gates together and had no intention of them being used for years and years, but, i did use a very well known and used wood screw brand, And have to say i was suprised at how fast the screws had corroded in a relatively short period of time. - The screws i had used were gold in colour, wax coated and supposedly corrosion resistant, but a year later tells a different story. - Even though the screws were painted over, the rust had started to show through, so i chose to remove and replace them all with Reisser cutter screws, which are gold tropicalized, so i hope and assume these will perform better. - I like the cutter screws for their ability to ‘bite’ in, pull in smooth and fast & self countersink cleanly. I haven’t had one strip a head or snap yet. They come with two free PZ2 bits in the tub, but they will wear down before you will get through all the screws, but what do you want for free! The tubs (this one is 4.0x40mm 1200 pcs) are a good size, made of strong plastic and even have a screw measure on the lid! - I think screws can often be compromised in relation to profits, i have often come across jobs were i have tried to remove a screw and it had a stripped head, rusted out or snapped trying to remove it. Using right type of screw for the application whether it be size, coating or type, is important, i always bin the screws that come with things like brackets & equipment as more often than not they are just cheap fixings that are soft and will rust! - So that’s my opinion, what screws do you use? Does it matter to you? Have you had a nightmare with a screw?! @reisser_ltd #doscrewsmatter #screws #rightscrewfortherightjob #reisser #reisserscrews #reisserscrewsuk #woodscrews #timberscrews #opinions (at Cornwall) https://www.instagram.com/p/CABL5BADOaa/?igshid=n7sfipyux6z1

Here is the FC Tools @hybridrailsquare router sled! I had the pleasure of meeting Frank at the @ffxtools show earlier in the year, he is a great guy with a passion for making good quality tools and accessories that solve problems! Frank’s company FC Tools are known for producing the hybrid railsquare & now offer a few more router related products including this router sled. Cnc’d from aluminum, the sled is made to last, the kit also comes with a cnc’d handle and stops which attach to the rail guide with a simple nylon screw which can be hand tightened. With no adjustments or moving parts, the sled is foolproof and set up takes seconds. The router attaches to the sled via the routers fixing holes for guide bushes & requires no special fixings, so keeps everything simple. In use the sled is smooth and precise, no wobble or binding. The sled is available for Dewalt & Makita cordless routers with the choice of Dewalt, Festool & Mafell guide rails, so there should be an option for everyone! #fctools #hybridrailsquare #routersled #fctoolsroutersled #router #dewaltrouter #dewaltcordlessrouter #makitarouter #makitacordlessrouter #festool #festoolguiderail #mafell #mafellguiderails (at Cornwall) https://www.instagram.com/p/B_FxzElDgFe/?igshid=1daffi9vm17yc

Day 1 of Rob & Barry’s @barry_pigeon Roadtrip! Being as the trade show over in cologne has been postponed due to the 😷 virus, we decided to do a little roadtrip and visit a few of our friends who just happen to work at some of the best companies! Yesterday saw us embark on our little tour and first stop was @bigwipes ! Visiting the infamous big yellow house has always been on my list! They do have rules though, all visitors Must bring cake! 🤣 We were very impressed with their location, the office and co-ordinating colour scheme! Purveyors of arguably the best wipes on the market, they are some of the nicest people to talk to and make a half decent cuppa too! 👍🏻 After, we headed up to brum! Up to see Mr Alex and his very modern @uniliteuk offices. Unilites office and warehouse is a very modern facility & radiated their professionalism. We were treated to a tour and a product overview and brief history of unilite. Building relationships with companies and end users results in better quality products through direct feedback, and the customer support you just can’t beat compared to the larger companies, as you will always speak to the same people and build a good customer relationship. @bigwipes @uniliteuk #bigwipes #bigwipesuk #unilite #uniliteuk #roadtrip (at Redditch) https://www.instagram.com/p/B9RMNS0DVWN/?igshid=1akejldvsvtug

C.K Tools VDE combicutter 3 These have been my favourite side cutters since my apprenticeship! These ones, my current ones, must be the 5/6th pair i have owned in over 15 years! 😲 I stay with them as i find them comfortable, compact and have a few useful features such as the 1.5 & 2.5 wire stripping notches, the wire bending anvil just above the grip, and the 3.5mm screw shearer. @c.k_tools #cktools #sidecutter #wirecutter #electriciantools #electrician #electriciansofinstagram #sparky #sparkylife #sparkylife⚡️ https://www.instagram.com/p/B87KOM8jA5x/?igshid=1sviyp1gepduh

𝗠𝗮𝗿𝗰𝗿𝗶𝘀𝘁 𝗤𝘂𝗶𝗰𝗸 𝗞𝗲𝘆𝗹𝗲𝘀𝘀 𝗔𝗻𝗴𝗹𝗲 𝗚𝗿𝗶𝗻𝗱𝗲𝗿 𝗙𝗹𝗮𝗻𝗴𝗲 Marcrist kindly sent me out one of their quick keyless angle grinder flanges to try out and use with their awesome 850 series cut off discs. This is the first time i have used a keyless flange on an angle grinder, and i now want another for my other grinder! I know these are nothing new, and there are other manufacturers making these, but the quality of this Marcrist flange is spot on. Having the ability to swap out discs easier and faster is more productive, And also cuts down time looking for that misplaced flange key! The keyless flange has a knurled outer edge for grip, and a sprung base with dimpled surface to resist vibration and hold the disc securely. This will fit any M14 threaded angle grinder and can be used with discs from 100 - 230mm. @marcrist_uk #marcrist #marcristkeylessflange #marcristquickkeylessflange #anglegrinder #anglegrinders #metalwork #metalworking #anglegrinderdisc #safety (at Cornwall) https://www.instagram.com/p/B8maz9yAbLA/?igshid=1pw6s0k040g6y

Nice little job today, making a cupboard to fit underneath an existing sink and top. As the existing top was not level, first job was to remove all supports and level out the top before i could take any measurements for the cupboard. All fixings were pocket holes from the inside using the @kregjig K4, so no visible fixings externally. Internal shelf has a soft wood lip to protect against knocks. I used @swankyscribe to get the skirt scribes nice & tight. I tried out my new @reisser_ltd 35mm forstner bit to let in the Hafele soft close clip on hinges into the doors. #bespokecupboard #bespokecupboards #undersinkcabinet #undersinkstorage #undersinkcupboard #cupboard #carpentry #carpenter #chippy #cornwall #cornwallcoast #newquay #kernow (at Newquay, Cornwall) https://www.instagram.com/p/B8e1i4MjM6l/?igshid=1qlorr5x2n5cj

Last weekend i decided to rip out this trim from our stairs at home, in my on going never seemingly ending quest to banish any gloss wood work, i decided to made a new trim. I had a couple of pieces of Howdens burford contemporary architrave, and come up with a wrap around idea that i thought would look & finish nicer. Using the dewalt flexvolt table saw with a keyblades blade, i ripped down the architrave @ 45 degree angle, then joined the two halves together with some titebond 2 & some collins (dick & balls) clamps! 😆 I think it came out ok, could be better, but as nothing is dead straight there are a few small gaps 😐 Just need to get some wax filler on the fixing holes and should be good for some osmo oil love! @keybladesandfixings @howdensjoinery @titebondproducts @osmo_uk #woodworking #woodwork #oakveneer #architrave #stairtrim #stairtrims #stairaprons #oak #keybladesandfixings #dewalttoolsuk #osmooil #cornwall #kernow (at Cornwall) https://www.instagram.com/p/B8B1WAMAT1a/?igshid=16lps0liqfahl

Today’s job! To add a couple of matching cupboards and a new worktop. @howdensjoinery over in Newquay supplied me with a 600 drawerline base, 500 wall unit, pelmet, doors and drawer front, new worktop and end panel. The base unit wasn’t an issue to fit, just a small cut out at the back for pipes, but the wall unit was a headache! A smaller unit would have fitted easier, but lose storage space and would mean a large filler panel. I had to cut 15mm off the corner to get the unit to fit snug . There were also pipes to contend with at the back of the unit, which meant a small cut out at the back. The @hultafors dry marker came into its own for marking through the back of the carcass, while @swankyscribe took care of scribe marking duties! As always, @keybladesandfixings blades and jigsaw blades for all cuts and @reisser_ltd screws to hold everything together! I need to pop back to silicone the worktop and to fix my little cock up! 😂 did you spot it? #kitchen #kitchencupboard #kitchencabinets #kitchencupboards #kitchenunits #worktop #worktops #addon #howdens #newquay #staustell #kernow #cornwall #carpentry (at Saint Austell) https://www.instagram.com/p/B74K7WIAWyT/?igshid=11mejguctcjah

A little door swap out this morning , replacing this tired brown flat panel door with a 6 panel door, with new polished brass furniture . I had the door dream team out for this, @trendtooltechnology skeleton hinge jig @dewalttoolsuk 18v cordless router @keybladesandfixings long shank 12mm straight cutter @hultafors deadblow mallet and chisels Also used my new @trendtooltechnology snappy self centering drill bits, a lot better than my old cheap ones!! 😆 Handles, latch & hinges from @screwfix_uk , even came with a cleaning cloth for the handles 👍🏻 #door #doors #internaldoors #internaldoor #doorswap #doorhanging #hangingdoor #doorhandle #trendhingejig #keybladesandfixings #dewalttoolsuk #hultafors #chisels #routerbits #cornwall #kernow #staustell #carpenter #carpentry (at St Blazey Gate) https://www.instagram.com/p/B704ImbgGuP/?igshid=dunds9j55jv9

Spent this morning running around looking for and collecting materials, then this afternoon on a bunch of maintenance jobs at a house and a flat for a client. Had to replace a handle and latch with a new handle and bathroom sash lock as the old one jammed and trapped someone in! 😆 Did a bunch of small maintenance jobs (in my stories) and also fitted some heavy duty trellis to a garden fence. The @stabila_uk illuminated levels came into their own when the light began to fade 👌🏻 #maintenance #housemaintenance #flatmaintenance #electrical #electrics #electrician #sparks #carpentry #carpenter #chippy #doorlock #bathroom #bathroomlock #gardenfencing #newquay #cornwall #kernow (at Newquay, Cornwall) https://www.instagram.com/p/B7rWl-LAyJn/?igshid=tumak2lxs8xq

Router Bits Have you tried Keyblades & Fixings router bits yet? Keyblades are well known for their excellent but modestly priced saw blades, but also offer many other own branded products like these router bits. I have been using them since they first launched their straight router cutters, but they have recently expanded their range with some round over, top bearing flush cut, bottom bearing flush cut, a long shank (70mm) 12mm (ideal for hinge jigs) and some other sizes. The packaging catches the eye, and is very eco friendly and recyclable being made from cardboard. The bits look and feel to be of excellent quality and so far, have kept their edge well. If you like the look of these bits, or are curious to try them, head over to their website, they are currently in their sale! But be quick! #keybladesandfixings #keyblades #keybladesrouterbits #routerbits #routerbit #router #cordlessrouter #carpentrytools #woodworkingtools #ukcompany (at Cornwall) https://www.instagram.com/p/B7om_cMgbzi/?igshid=154griwjjppng

So a year ago I decided to go self employed and turn my Instagram name & logo into a business! A year on, im still here! They say the first 18 months are the hardest for any business. Having come from working for a company for a solid 18 years, used to working with the same people and apprentice, starting up on my own was a intimidating and doing it the other side of the country and not knowing anyone, scary! It hasn’t been an easy year by anymeans, but it sure could have been a lot worse! I have spent the year working to pay bills, working on getting a good reputation, networking and making friends. I have learnt so much, some as a natural progression, some as a need to and some the hard way! 😂 I would like to say thank you to everyone who has given me advice, support, believed in me and supported my decision and me. Everyone starts somewhere, hopefully this is just the beginning 😎 #1year #1yearanniversary #1yearinbusiness #smallbusiness #smallbusinessowner #careerpath #makeyourself #successisinyourhands #tryharder #workhardstayhumble #tradesman #cornwall #kernow (at Cornwall) https://www.instagram.com/p/B7b3vKVAIi1/?igshid=1vie077mvnkap

CCTV Upgrade So the end of last week saw me drive up to Uxbridge to upgrade and install a new cctv system on a farm for my good ol mate @barry_pigeon . As the farm is used more as a commercial yard and with quite a bit of traffic entering & exiting, we opted to install a number plate recognition camera Hikvision DS-2CD4A26FWD-IZS/P, x6 DS-2CD2385G1-I dark fighter turrets, and a DS-7616NI-K2/16P NVR with 4TB to give a good all round surveillance. As the system was installed across several different buildings, some of the cable routes required a catenary wire to support the cables between buildings. We took the opportunity to improve the lighting by the main gate too, by installing a new post & x2 led flood lights from @screwfix_uk controlled by a photocell, to cover the gate and yard. A massive improvement over the old analogue system! Thank you to @barry_pigeon for having me, and for keeping me fed & watered, it was great working with you bud! 😜 #cctv #cctvsystem #cctvsystems #ipcctv #hikvision #security #ledfloodlight #screwfix #numberplatecamera #securitylighting #securitylight #uxbridge #slough #berkshire (at Uxbridge) https://www.instagram.com/p/B7T84-ngj6L/?igshid=m4enp1k4ih8r

Thats a wrap! Completed our relight of @staustellmarkethouse late this afternoon, and i am very happy with the results! 😎 Myself and my main man Paul worked solidly to get this cracked out in two days, all new @collingwoodled 100w led floods (color temp changeable) , replaced all old jb’s and connections with @wiskaukltd boxes, new glands, and a lot of @wagolimited connectors! This is part of a much bigger renovation project to give some much needed tlc and breathe some new life into this iconic local building. This is a fantastic space with a huge amount of character & history. It is also starting to become a hub for makers and creatives! Big thank you to @cef_staustell for amazing service as always, & Travis Perkins par & wadebridge for sorting out the tower for us 👍🏻 #relight #lightreplacement #ledlights #ledfloodlight #ledfloodlights #collingwoodled #collingwoodledfloodlight #wiska #wiskalifa #wiskahoppmann #wiskabox #wago #wagoconnectors #themarkethousestaustell #staustellmarkethouse #markethouse #staustell #staustelltown #cornwall #kernow #electrician #electricianlife #spark #sparky #sparkylife (at The St.Austell Market House) https://www.instagram.com/p/B6BuA8KAP4A/?igshid=1t8ii5ujtjqyl

Heres how the little under eaves cupboard i made the other week finished up! The home owner wanted a small cupboard to best utilize an otherwise awkward space. They didn’t want any details or mouldings, just plain and to blend in so as not to really be noticed, i think it worked 👍🏻 #bespokecupboard #bespokecupboards #undereavesstorage #undereavescupboard #bespokecarpentry #cupboard #cupboardstorage #bespokestorage #bespokestoragesolutions #kernow #kernowlife (at Nansledan Newquay) https://www.instagram.com/p/B500BakgP6a/?igshid=1jo8hir4xlajn