#stp cable

Différents types de câbles réseau sont utilisés pour transférer des données entre ordinateurs, imprimantes, routeurs, commutateurs et autres. Pinsol propose divers câbles réseau à un coût abordable tels que FTP, STP, etc. Si vous souhaitez un ingénieur réseau professionnel et expérimenté, contactez simplement notre équipe.

If anyone wants to transfer online data from one computer to another then think about network cable. Today various types of cable are available at Pinsol stores such as copper cable, and optical cable. Networking is a basic need in offices, commercial, and in residential buildings for sharing information.

To build your Ethernet network, the transmission media Ethernet cable is indispensable. And there are a variety of choices for Ethernet cables, such as Cat5e, Cat6, Cat6a and so on. If you are familiar with the differences between these different types of Ethernet cables, you may think it’s very simple to choose the right Ethernet cable for your network. However, is this really enough to help you make the decision? Are there any other factors you have to take into consideration? This article will give you the answer.

Overview of Different Types of Ethernet Cables

First, let’s have a quick review of the basic knowledge of these different types of Ethernet cables. For data speed, Cat5e is designed to support 1 Gigabit Ethernet with bandwidth up to 100MHz; Cat6 can support higher data rate of 10 Gigabit Ethernet with bandwidth up to 250 MHz; Cat6a is defined at frequencies up to 500MHz among 10G Ethernet applications. For transmission distance, Cat5e can reach 100 meters at the speed of 1Gbps; Cat6 is able to run 100 meters with data speed up to 1Gbps and only 55 meters at the speed of 10Gbps; Cat6a can support the distance over 100 meters at the speed of 10Gbps. Which types of Ethernet cables to choose depends on your requirement for transmission speed and distance. After you make a decision on this, there are some other factors you have to consider—straight-through or crossover cable, UTP (unshielded twisted pair) or STP (shielded twisted pair) cable, length and color. The following part will focus on these factors.

Straight-Through or Crossover Cable?

Ethernet cable terminated with RJ45 connector contains eight color-coded wires. The color-coded wiring sequences exist as a cabling industry standard. When linking RJ45 connector to a cable, there are two wiring standards—T-568A and T-568B. The two wiring standards are used to create a straight-through cable (T-568A or T-568B on both ends), or a crossover cable (T-568A on one end and T-568B on the other end). To choose a straight-through cable, you have to use either T-568A or T-568B on both ends of the cable; to choose a crossover cable, you need to wire T-568A on one end and T-568B on the other end of the cable. Here is a figure of T-568A and T-568B, from which you can see the difference between these two wiring standards.

UTP or STP Cable?

STP cable has a metal shield around each twisted pair which is composed of copper tape, a layer of conducting polymer or a braid (mostly made of copper or aluminum). With the shield, EMI (electromagnetic interference) and crosstalk can be greatly reduced, which enables the high performance of data transmission between different devices. While UTP cable has no shielding. It is designed to cancel electromagnetic interference through the way the pairs are twisted inside the cable. If the Ethernet cable runs in the environment where the interference or crosstalk is not the main concern, it is suggested to choose UTP cables which are lower in cost. But if the environment is full of powerful magnetic fields which may have an influence on the performance of network, STP cable is absolutely the optimal choice. To have a better understanding of the difference between UTP cable and STP cable, here is figure of the inner structure of UTP cable and STP cable.

Length and Color

When choosing Ether cable for your network, you also need to consider length and color. Ethernet cable comes in standard lengths such as 1, 3, 5, 7, and 10 meter. Longer lengths are available, such as bulk Cat5e cable 305m. The distance between your various network devices and your network switch or router will determine the length you need. In addition, Ethernet cable is designed in all sorts of colors, such as blue, gray, red and some other color. This decision can be based purely on your individual taste and preference.

Conclusion

Copper-based cabling has held the dominate position as the most prevalent horizontal cable medium for years. The reason of this can be partly explained by the fact that copper cable is inexpensive and easy to install. Additionally, the networking devices associated with copper cabling are less costly compared with their fiber optic counterparts. Copper cable comes in a dazzling array of types, and since cable type determines the network’s topology, protocol, and size, understanding the features of each copper cable is necessary for the installation of a successful and robust network.

Copper Cable Types at First Glance

By far the widely installed and most economical copper cable today is twisted-pair wiring. In this form of wiring, two conductors are wound together (“twisted”) for the purposes of canceling out electromagnetic interference (EMI) from external sources, and crosstalk from neighboring conductors. Unshielded twisted pair (UTP) and shielded or screened twisted pair (STP or ScTP) are the two primary varieties of twisted pair on the market today. Screened twisted pair (ScTP) is a variant of STP. Next, we will focus on the characteristics and possible applications of them.

Unshielded Twisted Pair (UTP)

Unshielded twisted pair (UTP) copper cable has been used in telephone systems for many years. And it was also intensively applied in local area networks (LANs) since late 1980s. UTP cabling typically has only an outer covering (jacket), which covers one or more pairs of wire that are twisted together. The lack of shielding enables a high degree of flexibility and durability, lower cost and simpler installation of UTP. During the past years, the bandwidth capabilities of UTP are consistently being improved, making it popular especially in computer networking. Four-pair UTP cables are often used for horizontal cabling, while multi-pair (25-,50-, or 100-pair) UTP cable is more commonly seen in backbone cabling.

Features of UTP are listed below:

Four-pair cables are typically used for horizontal cabling. Higher pair counts are often used for backbone cabling.

Its conductors are not surrounded by a metallic shield to prevent electrostatic or electromagnetic coupling.

Shielded Twisted Pair (STP)

Shielded twisted-pair copper cable has a metallic shield which significantly reduces the instances of interference-related network problems. Though more expensive to purchase and install than UTP, STP offers some distinct advantages: it is less susceptible to outside electromagnetic interference (EMI) than UTP cabling since all cable pairs are well shielded. As with UTP, four-pair cables are typically used for horizontal cabling. When it comes to STP, four-pair cables are offered in two versions:

Four-Pair Screened Twisted-Pair (F/UTP)

F/UTP (also referred to as ScTP) copper cable has an outer metal shielding covering the entire group of copper pairs. This type of shielding protects the cable from external EMI; however, the shield and drain wire add cost as well as size. The shield and drain wire also require bonding and grounding. F/UTP is recommended for use in hospitals, airports, or government/military communications centers.

Four-Pair Shielded Twisted-Pair (U/FTP)

U/FTP (also referred to as STP) copper cable includes metal shielding over each individual pair of copper wires. Besides protecting the cable from external EMI, U/FTP provides better near end crosstalk performance than F/UTP. However, the multiple shields also add more cost and size. Like F/UTP, the shield and drain wire require bonding and grounding.

Should I Choose Unshielded, Shielded, or Screened Copper Cable for Horizontal Cabling?

Network managers and cabling infrastructure designers are constantly in the dilemma to choose between these copper cables. Here we offer a solution for your reference.

For typical office environments, UTP cable always serves as the best choice (until fiber network components drop in price). Most offices don’t experience anywhere near the amount of electromagnetic interference (EMI) necessary to justify the additional expense of installing shielded twisted-pair cabling.

As for environments like hospitals and airports, it would be more beneficial to apply a shielded or screened cabling system. The deciding factor seems to be the external field strength. If the external field strength does not exceed three volts per meter (V/m), good-quality UTP cabling should work fine. If the field strength exceeds three V/m, shielded cable will be a better choice.

Conclusion

We have illustrated the characteristics and possible uses of different types of copper cable in this article. When it comes to horizontal cabling, your choice should base on the specific cabling environment and condition. Hope what we discussed here could help you to make the right decision.

Twisted pair is the ordinary copper wire which connects home and many business computers to the telephone company. It is made by putting two separate insulated wires together in a twisted pattern and running them parallel to each other which helps to reduce crosstalk or electromagnetic induction between pairs of wires. Since some telephone sets or desktop locations require multiple connections, twisted pair is sometimes installed in two or more pairs, all within a single cable.

Twisted pair cable is good for transferring balanced differential signals. The practice of transmitting signals differentially dates back to the early days of telegraph and radio. The advantages of improved signal-to-noise ratio, crosstalk, and ground bounce that balanced signal transmission bring are particularly valuable in wide bandwidth and high fidelity systems.

How Does Twisted Pair Cable Work？

Twisted pair cable is widely used for telecommunications and most modern Ethernet networks. But do you know how a twisted pair cable works?

When electrical current flows through a wire, it creates a small, circular magnetic field around the wire. Noise is generated within signal lines through magnetic fields. Therefore the noise in data outlines is the consequence of the magnetic field. Within the straight cable connection, all sound current is moving in the same direction, exactly like within a regular transformer coils. Once the cable is actually twisted, their magnetic fields are opposite to each other. Thus, the two magnetic fields cancel each other and any outside magnetic fields. Due to this, the noise current in a twisted cable is lower than in an ordinary cable.

Types of Twisted Pair Cable

According to whether the cable has a shielding layer, there are two common types of twisted pair cables—shielded twisted pair cable and unshielded twisted pair cable.

Shielded Twisted Pair (STP) Cable

Shielded twisted pair (STP) cable combines the technique of shielding, cancellation and wire twisting. Each pair of wires is wrapped in a metallic foil. The four pairs of wires then are wrapped in an overall metallic braid of foil. STP cable is used to eliminate inductive and capacitive coupling. Twisting cancels out inductive coupling, while the shield eliminates capacitive coupling. This kind of cable is often applied between equipment, racks and buildings. Compared to unshielded twisted pair cable, STP will cause more attenuation. However, because in the case of balanced transmission, the complementing signals will effectively cancel out any shield currents, so the losses are negligible. Besides, although STP prevents interference better than UTP, it is more expensive and difficult to install.

Unshielded Twisted Pair (UTP) Cable

Unshielded twisted pair cable is the most commonly used cable for Ethernet connections. It consists of color-coded copper wires, but does not include any foil or braiding as insulator to protect against interference. In addition, the wires in each pair are twisted around each other. UTP cables are smaller than STP cables, which makes them easier to install, particularly in bulk or in narrow spaces. They are also cheaper than STP cables, and do not require as much maintenance, since they do not rely on outer shield. Furthermore, UTP cables can also transmit data as fast as STP cables. However, UTP cables are more prone to cause electrical noise and interference than other types of networking media. Thus, UTP cables are best used for domestic and office Ethernet connections, and in any area where there is not a high degree of electromagnetic interference.

Applications of Twisted Pair Cable

The most commonly used twisted pair cable impedance is 100 ohms. And it is widely deployed for data communications and telecommunication applications in structured cabling system. As its transmission distance&speed and bandwidth are limited, twisted pair cables are often used in telephone lines to carry voice and data channels, and local area network such as 10Base-T and 100Base-T, and so on.

Conclusion

Twisted-Pair Cable In traditional installations, the most economical and widely installed cabling today is twisted-pair wiring. Not only is twisted-pair wiring less expensive than other media, installation is also simpler, and the tools required to install it are not as costly. UTP and STP are the two primary varieties of twisted-pair on the market today. ScTP is a variant of STP.

Unshielded Twisted-Pair (UTP) Though it has been used for many years for telephone systems, UTP for LANs first became common in the late 1980s with the advent of Ethernet over twisted-pair wiring and the 10Base-T standard. UTP is cost effective and simple to install, and its bandwidth capabilities are continually being improved. NOTE: Alexander Graham Bell invented and patented twisted-pair cabling and an optical telephone in the 1880s. During that time, Bell offered to sell his company to Western Union for $100,000, but it refused to buy.

UTP cabling typically has only an outer covering (jacket) consisting of some type of nonconducting material. This jacket covers one or more pairs of wire that are twisted together. Four-pair cable is the most commonly used horizontal cable in network installations today. The characteristic impedance of UTP cable is 100-ohms plus or minus 15 percent, though 120-ohm UTP cable is sometimes used in Europe and is allowed by the ISO/IEC 11801 Ed. 2 cabling standard.

A typical UTP cable is shown below. This simple cable consists of a jacket that surrounds four twisted pairs. Each wire is covered by an insulation material with good dielectric properties. For data cables, this means that in addition to being electrically nonconductive, it must also have certain properties that allow good signal propagation.

UTP cabling seems to generate the lowest expectations of twisted-pair cable. Its great popularity is mostly due to the low cost and ease of installation. With every new generation of UTP cable, network engineers think they have reached the limits of the UTP cable’s bandwidth and capabilities. However, cable manufacturers continue to extend its capabilities. During the development of 10Base-T and a number of pre-10Base-T proprietary UTP Ethernet systems, critics said that UTP would never support data speeds of 10Mbps. Later, the skeptics said that UTP would never support data rates at 100Mbps. After that, the IEEE approved the 1000Base-T (1 Gb/s) standard in July 1999, which allows Gigabit Ethernet to run over Category 5 cable. Just when we thought this was the end of copper UTP-based applications, in 2006 the IEEE approved the 10GBase-T standard, which allows 10 Gigabit Ethernet over unshielded Category 6 and 6A cable!

Shielded Twisted-Pair (STP) STP cabling was first made popular by IBM when it introduced type classification for data cabling. Though more expensive to purchase and install than UTP, STP offers some distinct advantages. The current ANSI/TIA-568-C cabling standard recognizes IBM Type 1A horizontal cable, which supports frequency rates of up to 300MHz, but does not recommend it for new installations. STP cable is less susceptible to outside electromagnetic interference (EMI) than UTP cabling because all cable pairs are well shielded.

Some STP cabling, such as IBM types 1 and 1A cable, uses a woven copper-braided shield, which provides considerable protection against EMI. Inside the woven copper shield, STP consists of twisted pairs of wire (usually two pairs) wrapped in a foil shield. Some STP cables have only the foil shield around the wire pairs.

The figure below shows a typical STP cable. In the IBM design, the wire used in STP cable is 22 AWG (just a little larger than the 24 AWG wire used by typical UTP LAN cables) and has a nominal impedance of 150 ohms, but category versions can have a nominal impedance of 100 ohms.

Constructions of STP in 24 AWG, identical in copper conductor size to UTP cables, are more commonly used today.

Simply installing STP cabling does not guarantee you will improve a cable’s immunity to EMI or reduce the emissions from the cable. Several critical conditions must be met to achieve good shield performance:

The shield must be electrically continuous along the whole link.

All components in the link must be shielded. No UTP patch cords can be used.

The shield must fully enclose the pair, and the overall shield must fully enclose the core. Any gap in the shield covering is a source of EMI leakage.

The shield must be grounded at both ends of the link, and the building grounding system must conform to grounding standards (such as J-STD-607-A).

If even one of these conditions is not satisfied, shield performance will be badly degraded. For example, tests have shown that if the shield continuity is broken, the emissions from a shielded cabling system increase by 20dB on the average.

Screened Twisted-Pair (ScTP) A recognized cable type in the ANSI/TIA-568-C standard is ScTP cabling, a hybrid of STP and UTP cable. ScTP cable contains four pairs of unshielded 24 AWG, 100 ohm wire (see the figure below) surrounded by a foil shield or wrapper and a drain wire for grounding purposes. Therefore, ScTP is also sometimes called Foil Twisted-Pair (FTP) cable because the foil shield surrounds all four conductors. This foil shield is not as large as the woven copper-braided jacket used by some STP cabling systems, such as IBM types 1 and 1A. ScTP cable is essentially STP cabling that does not shield the individual pairs; the shield may also be smaller than some varieties of STP cabling.

The foil shield is the reason ScTP is less susceptible to noise. To implement a completely effective ScTP system, however, the shield continuity must be maintained throughout the entire channel, including patch panels, wall plates, and patch cords. Yes, you read this correctly; the continuity of not only the wires but also the shield must be maintained through connections. Like STP cabling, the entire system must be bonded to ground at both ends of each cable run, or you will have created a massive antenna, the frequencies of which are inversely proportional to the length of the shield. The net effect is that the noise is out of band.

Standard eight-position modular jacks (commonly called RJ-45s) do not have the ability to ensure a proper ground through the cable shield. So special mating hardware, jacks, patch panels, and even tools must be used to install an ScTP cabling system. Many manufacturers of ScTP cable and components exist (just be sure to follow all installation guidelines).

ScTP is recommended for use in environments that have abnormally high ambient electromagnetic interference, such as industrial work spaces, hospitals, airports, and government/military communications centers. For example, ScTP is used in fast-food restaurants that use wireless headsets for their drive-through-window workers; some wireless frequencies can interfere with Ethernet over copper. The value of an ScTP system in relation to its additional cost is sometimes questioned, as some tests indicate that UTP noise immunity and emissions characteristics are comparable with ScTP cabling systems. Often, the decision to use ScTP simply boils down to whether you want the warm and fuzzy feeling of knowing an extra shield is in place.

Screened Shielded Twisted-Pair (S/STP or S/FTP) S/STP cabling, also known as screened fully shielded twisted-pair (S/FTP), contains four individually shielded pairs of 24 AWG, 100 ohm wire surrounded by an outer metal shielding covering the entire group of shielded copper pairs. This type of cabling offers the best protection from interference from external sources, and also eliminates alien crosstalk (discussed later), allowing the greatest potential for higher speeds.

Category 7 is an S/STP cable standardized in ISO 11801 Ed. 2, which offers a usable bandwidth to 600MHz. Its intended use is for the 10 Gigabit Ethernet, 10GBase-T application. S/STP cable looks similar to the STP cable, but has four individually shielded conductor pairs.