#sharp on sight

Why Do My Knives Go Dull So Fast? (And What You Can Do About It)

If there’s one question that rivals “I just can’t get it sharp,” it’s this: “Why do my knives go dull so quickly?”

You sharpen, you slice, and before long that edge seems to vanish. Suddenly, you’re sawing through tomatoes or tearing up herbs instead of slicing cleanly. It can feel like your knives are betraying you—but the truth is, it’s rarely the knife’s fault. More often, it’s what happens after sharpening that shortens the edge’s lifespan.

As a professional sharpener serving Madison, Sun Prairie, Waunakee, and surrounding areas, I see the same culprits again and again. If you’re wondering why your knives don’t stay sharp, let’s break down the most common reasons—and more importantly, what you can do about it.

Let’s go through the biggest culprits—and the fixes—so you can keep your knives sharper, longer.

1. The Cutting Board Problem

Your cutting board is either your knife’s best friend or its worst enemy.

Glass cutting boards: These should come with warning labels. Every slice is like running your knife into a brick wall. They’ll kill an edge in one session.

Ceramic or granite boards: Same deal—hard as stone, because they literally are stone.

Bamboo: Looks great, but bamboo is dense and silica-rich. That natural grit acts like sandpaper on edges.

Plastic: A solid middle-ground. They’re cheap, easy to clean, but they do scar deeply. Once those grooves show up, bacteria can hide in there.

Wood (end grain or edge grain): This is the sweet spot. Wood has just enough give to keep your edge alive while staying sturdy enough for prep work. End grain boards, in particular, “self-heal” as the fibers close back up.

Fix it: Ditch the glass, stone, or bamboo boards. If you’re serious about sharp knives, invest in a good hardwood board. A solid maple or walnut board might feel like a splurge, but it will save you money on sharpening down the road.

2. The Dishwasher Mistake

Putting knives in the dishwasher is one of the fastest ways to ruin them. Why? Three reasons:

Heat: The high temps are brutal on handle materials and can even mess with cheaper steels.

Detergents: They’re formulated to scrub hard, and they’ll chew away at your blade’s fine edge.

Banging around: A knife tossed in with forks, spoons, and plates is going to hit things. Every bump dulls the edge.

Even a single cycle can undo hours of sharpening work.

Fix it: Hand wash your knives. Warm water, a drop of dish soap, a quick wipe with a sponge, then towel dry. Takes less than a minute and keeps your edge intact.

3. You’re Not Honing Enough

Here’s the truth: knives don’t usually go dull overnight—they just lose alignment. A honing rod doesn’t sharpen (no metal is removed); it simply straightens the microscopic edge that gets bent over during cutting.

If you skip honing, that rolled edge gets worse with every use until your knife feels completely dull.

The good news? You can’t really mess up honing. Forget all the diagrams and angles. Just hold the rod steady, swipe each side of the knife lightly from heel to tip a few times, and you’re done. Think of it like brushing your teeth—perfect technique matters less than simply doing it regularly.

Fix it: Keep your honing rod near where you prep food so you actually use it. Swipe the knife a few times once or twice a week if you cook often. It takes seconds and can easily double the lifespan of your sharpening.

4. Using Knives for the Wrong Jobs

This one’s easy: knives are for food. Not bones, not frozen hamburger bricks, not jars, not cans. Every time you misuse your kitchen knife, you’re taking months off its life.

Even little things matter. Scraping food off the cutting board with the knife’s edge is basically sanding it dull.

Fix it: Use the spine to scrape. Get a cleaver or heavy-duty knife for bones and frozen food. And if you’ve been known to pry open paint cans with your chef’s knife, please—don’t.

5. Bad Storage Habits

If your knives are rattling around in a drawer, you’re basically storing them in a rock tumbler. Every bump with a spoon, scissor, or drawer wall takes tiny chips out of the edge.

Fix it: Invest in safe storage. A wooden block, a magnetic strip, or even simple plastic blade guards will do. The goal is no contact between sharp edges and hard surfaces when the knife isn’t in use.

6. Sometimes It’s Just the Steel

Not all knife steels are the same.

Budget stainless (like 420HC or 4116): Easy to sharpen but dull quickly.

Mid-grade steels (VG-10, 14C28N): A solid balance between sharpness and retention.

Premium steels (M390, S35VN, CPM-M4): Hold an edge for ages but require diamond or ceramic abrasives to sharpen properly.

If your $20 grocery store knife dulls in a week, that’s not you—it’s the steel.

Fix it: Match your expectations to your knife. Softer steels need frequent touch-ups but sharpen easily. High-end steels hold an edge longer but take more work to bring back.

7. Over-Sharpening and Over-Polishing

This one surprises people. You can actually shorten the life of your knife by sharpening too often or polishing too far.

Sharpening removes steel. Do it unnecessarily and your knife loses material fast, eventually becoming thicker and harder to cut with. Polishing can also “round off” the apex if overdone, especially with sloppy stropping.

Fix it: Don’t sharpen just because the knife “feels” dull. Hone first. If honing doesn’t bring back bite, then sharpen. And when you do sharpen, aim for a practical finish. A toothy 800–1000 grit edge is usually better for food prep than a mirror polish.

8. Cutting Habits That Kill Edges

Some everyday habits you don’t even think about are hard on knives.

Twisting the blade when cutting dense food.

Chopping straight onto metal pans or plates.

Cutting directly on countertops.

Every one of these can chip, roll, or flatten your edge in seconds.

Fix it: Always cut on a proper board. Keep your cuts straight. And if you’re tempted to slice something directly on a plate for convenience—resist. Your knife will thank you.

9. Knives Don’t Stay Sharp Forever

Even with perfect care, knives will eventually need attention. But instead of memorizing a schedule, here’s how to think about it in the real world:

Everyday home cooking: Give your knife a quick hone once a week. When that no longer perks it up, it’s time for a professional sharpening.

Busy home kitchens (big families, lots of scratch cooking): If you’re chopping vegetables daily, breaking down roasts, or cooking every meal at home, hone often—every other day or so. When your knife still crushes tomatoes after honing, that’s your sign to call in a sharpener.

Restaurants and professional kitchens: Line cooks live on their knives. Daily honing is a must, and even then, the volume of prep work means professional sharpening will be needed regularly to keep pace with the workload.

Fix it: Think of sharpening like car maintenance. Tires wear down. Oil needs changing. Knives need service, too.

10. Sometimes It’s Time for a Professional

You can hone faithfully, use the right cutting board, hand-wash, and store carefully—and still end up with a knife that won’t cut the way you want. Chips, bends, or just years of use add up.

That’s where I come in. At Sharp On Sight, I reset edges, re-profile bevels, and bring knives back to life. Whether it’s a $30 workhorse or a $300 heirloom, I don’t send a knife back until it slices like it should.

Knife Sharpening Madison WI – Keeping Your Knives Going Strong

If you’re in the Madison, Sun Prairie, or Waunakee area and you’re tired of fighting dull knives, here’s how I can help:

Live sharpening – Every Saturday at the Sun Prairie Farmers Market (7 a.m.–Noon).

Drop-off sharpening – Anytime at 215 E Main Street, Sun Prairie (drop box just inside the front door, code 299181).

On-site sharpening – Available in the Madison area (extra fee for fewer than 10 items).

I sharpen everything from everyday kitchen knives to high-end Japanese blades, plus scissors, shears, yard tools, and more.

So if you’ve caught yourself wondering, “Why do my knives go dull so fast?”, know that it’s not just you. Knives are tools—they wear down. But with the right habits (and a little professional help when needed), you can keep them sharp, safe, and ready for whatever you’re cooking next

Why Sharp On Sight Started Carrying USA-Made Anza Knives

For a long time, Sharp On Sight has focused on one thing: edges. Not trends. Not hype. Just making tools cut the way they’re supposed to cut. That focus hasn’t changed. What has changed is that customers kept asking the same question over and over again:

“Do you sell knives too?”

Until now, the honest answer was usually some version of not really. I sharpened what people already owned. I fixed chipped edges, corrected factory mistakes, and brought worn‑out knives back into service. But after years of sharpening everything from kitchen knives to hunting blades, one thing became clear — some knives are simply built better than others, and some manufacturers stand behind their work in a way that actually matters.

That’s where Anza Knives came into the picture.

This post is about why Sharp On Sight decided to start offering Anza Knives, what makes them different, and where you can see them in person.

---

Why Become a Knife Dealer at All?

Sharpening gives you a front‑row seat to reality.

You see which knives respond well to proper sharpening and which ones fight you every step of the way. You see heat damage, over‑ground factory edges, poor steel choices, and designs that look good online but fail in real use. Over time, patterns emerge.

A lot of people assume that a dull knife means a bad knife. That’s rarely true. More often, it’s a decent knife that’s been sharpened incorrectly, overheated, or simply neglected. But there are knives that consistently hold up better under use and sharpening — and just as important, there are companies that don’t disappear when something goes wrong.

If Sharp On Sight was going to offer knives at all, they had to meet a few non‑negotiables:

Made entirely in the USA

Designed for real use, not display cases

Steel that sharpens well and performs honestly

A warranty that actually means something

That list is shorter than you might think.

---

Why Anza Knives?

I carry an Anza knife daily. Not as a show piece, not as a backup - it's the knife that's actually on me. After sharpening and working on thousands of blades, I'm picky about what earns that spot. Having firsthand experience with Anza knives, from edge performance to long-term durability, make them easy to trust. They sharpen cleanly, hold an honest edge, and they've proven reliable enough that I don't have to think twice about carrying one. 

Anza Knives checks every one of those boxes.

Anza has been making knives in the United States for decades, using high‑carbon steel reclaimed from industrial files. Each knife is individually ground, heat treated, and finished by hand. No two are exactly alike, and that’s not marketing language — it’s reality.

From a sharpener’s perspective, Anza knives stand out for a few key reasons:

High‑Carbon Steel That Makes Sense

High‑carbon steel isn’t exotic. It doesn’t chase edge retention charts or lab numbers. What it does offer is predictable sharpening behavior, excellent bite, and easy maintenance. When an Anza knife gets dull, it comes back quickly. When it takes damage, it can be repaired without fighting brittle steel or mystery heat treatments.

That matters for people who actually use their knives.

Built for Work, Not Trends

Anza knives aren’t trying to be everything to everyone. They’re fixed blades meant to be carried, used, and sharpened over and over again. No coatings to hide grind marks. No fragile geometry meant only for photos. What you see is what you get.

From hunting and camp tasks to general outdoor use, these knives are tools first.

Lifetime Warranty That’s Straightforward

Anza offers a lifetime warranty. If the knife breaks under normal use, they repair or replace it. No fine print games. No disposable mindset.

That aligns perfectly with how Sharp On Sight already operates. The goal isn’t constant replacement — it’s long‑term use.

---

Why This Makes Sense for Sharp On Sight

Selling knives isn’t a pivot away from sharpening. It’s an extension of it.

Every Anza knife sold through Sharp On Sight is backed by the same sharpening knowledge that’s applied to customer knives every week. That means:

Edges are set correctly from the start

Geometry is explained, not ignored

Maintenance is part of the conversation

When you buy a knife online, you get a box and a factory edge of unknown quality. When you buy a knife in person from someone who sharpens for a living, you get context.

You get to ask questions. You get to understand what the steel will do. And you get a knife that’s meant to stay in service, not end up in a drawer.

---

Not Every Knife Is Right for Everyone

This part matters.

Anza knives aren’t stainless. They will patina. They require basic care. If someone wants a knife they can throw wet into a backpack for a year and forget about, this probably isn’t the right choice.

But for people who appreciate tools, who understand that maintenance is part of ownership, Anza knives make a lot of sense.

They sharpen cleanly. They cut aggressively. And they reward good habits.

---

Seeing Anza Knives in Person

One of the biggest advantages of offering knives locally is that you don’t have to guess.

You can handle them. You can feel the balance. You can see the grind lines and handle variations. No stock photos. No exaggerated descriptions.

Sun Prairie Farmers Market

You can find Sharp On Sight every Saturday at the Sun Prairie Farmers Market, where Anza knives are available to see in person alongside live sharpening services. It’s a chance to talk through use cases, maintenance, and edge preferences face‑to‑face.

Outdoor and Gun Shows

In addition to the market, Sharp On Sight appears at select outdoor shows and gun shows throughout the year. These events are a natural fit for Anza knives — people who hunt, camp, fish, or spend time outdoors tend to understand the value of a well‑made fixed blade.

Availability may vary by event, but the focus stays the same: USA‑made knives, honest steel, and real tools.

---

Sharpening Still Comes First

It’s worth saying clearly — Sharp On Sight is still a sharpening business.

Becoming a knife dealer doesn’t change that foundation. If anything, it reinforces it. Every knife sold is a knife that can be maintained properly for years. Every conversation starts with use, not sales pressure.

Whether someone brings in a 20‑year‑old hunting knife or picks up a new Anza blade, the approach is the same: set the edge correctly, explain how to keep it that way, and avoid gimmicks.

---

A More Sustainable Way to Think About Knives

There’s a lot of noise in the knife world — constant new models, steel hype, limited runs, and disposable thinking. Anza knives sit outside of that cycle.

They’re not meant to be replaced next year. They’re meant to be used, sharpened, and carried.

That philosophy matches Sharp On Sight’s core belief: a good edge, properly maintained, matters more than chasing the next thing.

---

Looking Ahead

Adding Anza Knives is just the beginning of this chapter. The goal isn’t to become a massive knife retailer. The goal is to offer a small, intentional selection of knives that make sense for real users — knives I’d carry myself and sharpen without hesitation.

If you’re curious about Anza knives, want to handle one in person, or just want to talk through whether a fixed blade even makes sense for you, stop by the Sun Prairie Farmers Market on a Saturday or catch Sharp On Sight at an outdoor or gun show.

And if you already have a knife you like, that’s fine too. Just don’t neglect it. A good edge still goes a long way — and it only stays that way with proper maintenance. Bring it by for sharpening, have the edge corrected, and keep using the knife you already trust.

Why Your At-Home Knife Sharpener Isn’t Getting the Job Done

If you’ve ever run your kitchen knife through a pull-through sharpener or pressed it against a countertop “V” style sharpener only to discover it still struggles to slice a tomato, you’re not alone. The problem isn’t your knife — it’s the sharpener.

Most at-home knife sharpeners simply aren’t aggressive enough to restore a truly dull edge. They’re made to hone, not sharpen, and that’s a key difference most packaging doesn’t bother to explain. The result is a generation of kitchen knives that feel perpetually “almost sharp,” no matter how many times they’re dragged through those little slots.

Let’s break down exactly what’s happening, why your knives stay dull, and what you can do to fix it — once and for all.

---

Honing vs. Sharpening: The Difference No One Tells You About

Here’s the short version:

Honing realigns your existing edge.

Sharpening removes metal to create a new edge.

When you use a honing rod or a pull-through sharpener, you’re basically nudging the bent portion of your knife’s edge back into place. Think of it like brushing your hair — you’re straightening it, not cutting it.

But once that edge is worn away, there’s nothing left to “realign.” You need to grind away new material and form a fresh apex. That’s sharpening — and it requires an abrasive surface aggressive enough to remove steel. Most home devices just don’t have that capability.

---

Why Most Consumer Sharpeners Fail

Manufacturers know that the average home cook doesn’t want sparks flying or metal dust on their countertop. So, they build sharpeners that are safe, but not effective. 

Here’s what’s really going on:

1. Weak abrasives — The wheels or rods inside consumer sharpeners are often coated in fine ceramic or low-grit carbide that can’t bite deep enough into hardened steel.

2. Fixed angles — The sharpening slots are set to one universal angle, usually around 20° per side, which may not match your knife’s actual geometry.

3. Limited pressure — The spring tension or preset slot design prevents you from applying enough force to actually remove metal.

4. Marketing illusion — The term “sharpener” gets used loosely. Many are actually honing devices — designed to maintain sharpness, not create it.

In other words, you’re trying to do surgery with a butter knife.

---

The Result: A Polished, Dull Knife

What you end up with is a knife that looks better under light but still can’t cut worth a damn. You’ve polished the dull edge — you haven’t rebuilt it. Here’s the telltale sign: if your knife still pushes through food instead of gliding, it’s not sharp — no matter how glossy that edge looks.

A true sharpened edge should:

Slice through a tomato without pressure.

Cleanly shave paper or hair.

Feel slightly “grippy” when you touch the edge (carefully).

That’s what an aggressive sharpening process produces — and it’s something most countertop sharpeners can’t replicate.

---

Why “Aggressive” Isn’t a Bad Word in Sharpening

When professional sharpeners talk about being “aggressive,” we’re not talking about hacking away steel carelessly. We’re talking about using the right abrasives and pressure to reestablish the correct geometry of a blade. Think of your knife edge as a microscopic triangle. Over time, the tip of that triangle wears down or folds over. The only way to restore it is by grinding away enough material to form a new apex — sharp enough to split hairs.

To do that, you need:

Proper grit progression (coarse to fine).

Correct angles for the steel type and purpose.

Consistent pressure and control.

Most consumer sharpeners skip the first two entirely — and you end up with a “sort-of sharp” knife that dulls again within days.

---

Why Pull-Through Sharpeners Can Make Things Worse

A lot of people think, “At least I’m doing something!” But unfortunately, many pull-through sharpeners actually damage knives over time.

Here’s how:

They grind unevenly, removing more metal from one side.

They create wire edges — thin, fragile burrs that feel sharp but crumble after a few cuts.

They overheat softer steels, especially on inexpensive knives, which can reduce hardness and edge retention.

So even though it feels like your knife is sharper right after using one, that edge rarely lasts.

A professional sharpener, on the other hand, removes material strategically and polishes the apex to a stable, long-lasting finish — whether that’s a 15°, 18°, or 25° per side edge depending on the knife’s job.

---

The Hidden Cost of “Convenience” Sharpeners

The irony is that these “easy” sharpeners cost you more in the long run. Every time you use one incorrectly, you’re removing metal unevenly, shortening the life of your knife.

A good knife — even a mid-range one — should last decades if maintained properly. But a knife repeatedly run through cheap sharpeners may lose years of life in just a few months.

It’s like using sandpaper on your car windshield because it makes it “clearer.” Technically true, but only once.

---

Signs Your Knife Needs More Than Honing

If you’re not sure whether your knife just needs a touch-up or a full resharpening, here’s how to tell:

1. It slips off tomato skin or onion layers.

2. It requires force to cut through meat or vegetables.

3. The edge looks rounded under light.

4. It hasn’t been professionally sharpened in over six months.

5. You’ve been using a pull-through sharpener with no improvement.

If any of these sound familiar, it’s time to have the edge reset — not just “maintained.”

---

What a Professional Sharpener Actually Does

Professional knife sharpeners don’t rely on one angle or one abrasive. Every knife is assessed individually:

Angle correction: A pocket knife might need 25° per side for toughness, while a Japanese chef’s knife performs best at 15°.

Steel response: Some steels, like VG-10 or M390, require more aggressive abrasives and longer refinement steps.

Heat control: Proper sharpening avoids overheating, which can ruin temper and destroy hardness.

Edge refinement: After establishing a new apex, we refine the edge through progressively finer grits and finish with a strop or polish.

At Sharp On Sight, for example, we reset dull edges using controlled abrasives — the kind that remove metal efficiently but precisely. The result? A sharper, more durable edge that lasts through months of daily use.

---

The Science Behind “Aggression”

The idea that “gentle” is better doesn’t apply to knife sharpening. Steel is tough — and you need abrasives tough enough to reshape it.

Let’s put it in perspective:

A human fingernail is about 2.5 on the Mohs hardness scale.

Steel is usually between 55–65 Rockwell (around 7–8 Mohs).

Many consumer ceramic sharpeners barely reach 9 Mohs — meaning they can only scratch, not grind, certain steels effectively.

Professional sharpening systems use industrial belts, diamond plates, or bonded abrasives capable of cutting even premium steels like S35VN or M390. That’s what separates “sharpened” from “maintained.”

---

Why Consistency Beats Convenience

Even if you somehow manage to get a knife sharp at home, consistency is almost impossible. Slight angle changes make a huge difference.

Uneven strokes create asymmetrical bevels.

Inconsistent pressure means a weak edge that dulls fast.

Professional sharpeners use tools that lock in consistent angles and maintain precise control. That’s why a knife sharpened professionally not only cuts better — it stays sharp longer.

---

The Sharpening Angle Myth

Most home devices sharpen everything at the same preset angle — but not all knives should have the same geometry.

Japanese knives (like Santokus or Nakiris): 15° per side for fine slicing.

Western chef’s knives: 18°–20° for general durability.

Pocket and outdoor knives: 25° or more for toughness.

When your at-home sharpener locks you into a single angle, it’s forcing every knife into the same mold — which almost guarantees at least one will perform worse. That’s why custom angle sharpening matters.

---

When to Use a Home Sharpener — and When Not To

There’s still a place for honing rods and gentle ceramic tools. They’re great for:

Touching up an edge that’s already sharp.

Realigning micro-burrs between professional sharpenings.

Maintaining a knife’s performance day-to-day.

But once a knife loses its bite completely, those tools can’t rebuild the edge. That’s when it’s time to hand it over to a professional.

---

Professional Knife Sharpening in Madison and Sun Prairie

If you’re tired of dull knives that never seem to stay sharp no matter how often you “sharpen” them, it’s probably because you’ve been honing, not sharpening.

At Sharp On Sight, we specialize in restoring the edge correctly — using aggressive, controlled methods designed for each blade type. We sharpen all knives, scissors, yard tools, clippers, and even serrated edges.

Whether you drop them off at 215 E Main Street, Sun Prairie, or visit our live sharpening booth at the Sun Prairie Farmers Market, we’ll make sure your knives cut like they should again.

You can search knife sharpening Madison WI, professional sharpening Sun Prairie, or just look for the Sharp On Sight booth — and you’ll know your knives are in good hands.

---

Stop “Maintaining” Dullness

At-home sharpeners aren’t inherently bad — they’re just misunderstood. They’re maintenance tools, not repair tools.

Once your edge is gone, you can’t coax it back with a few passes through a slot. You need a proper grind, precise angles, and the right abrasives.

If your knives used to glide and now just drag, it’s not your fault — it’s your sharpener’s. Let a professional reset the edge and then use your home tools for upkeep. That’s the secret to always-sharp knives and stress-free cooking.

A clean grind, a confident lock, and jimping that actually works when you need it. The Eutektik EFD pocket knife brings utility and style together in a way that makes it a keeper in any rotation.

Mother’s Day is coming up. She doesn’t need another candle.

Take care of the tools she actually uses. Knives, scissors, garden tools—sharp and ready to go.

Serrated knives get replaced for one simple reason. They stop cutting, and most people don’t deal with the part that actually dulls. It looks complicated, so it gets ignored.

Serrated knife sharpening can restore that edge instead of replacing it. If your bread knife or steak knives aren’t cutting, they likely just need proper sharpening. Serving Madison WI and Sun Prairie.

One of the biggest misconceptions is that clipper blades are supposed to be perfectly flat. In reality, they are not. Both the comb and the cutter are manufactured with a very slight convex shape on the inside surfaces where the two blades meet.

That subtle convex shape is intentional. It allows the tips of the teeth on the cutter and comb to be the primary contact points. When the clipper is running, the cutter slides back and forth thousands of times per minute while the spring tension pushes it upward so the tips of the teeth barely press together. That light contact at the tooth tips creates the shearing action that cuts hair cleanly.

If the blades were perfectly flat and touching across the entire surface, friction would increase dramatically. The blades would run hotter, the motor would work harder, and the cutting performance would actually suffer.

This is why sharpening clipper blades requires careful technique. Removing too much material or applying uneven pressure during sharpening can flatten out that slight convex. When that happens, the blades begin contacting across a larger area instead of just at the tooth tips. The blade may look freshly sharpened, but it will struggle to cut properly.

Because the tolerances are so small, even minor mistakes during sharpening can change how the blade performs. The goal is not simply to make the blade shiny or smooth. The real objective is preserving the subtle geometry that allows the cutter and comb to meet exactly where they should for clean, efficient cutting.

If your hair clippers stop cutting cleanly and start pulling hair, the problem usually is not the motor. In most cases the clipper blades are simply dull. A quick sharpening on a honing wheel with the proper abrasive can restore clipper blades in seconds and bring them back to cutting smoothly again.

In this short demonstration I show how dull clipper blades that will not cut hair can be quickly restored so the clippers cut cleanly again. Many people replace clippers when they stop working properly, but sharpening the clipper blades is often all that is needed.

Proper clipper blade maintenance keeps barber clippers, grooming clippers, and pet grooming clippers performing the way they were designed to.

If your clippers are pulling hair or not cutting evenly, the blades may just need sharpening.

Sharp On Sight provides professional sharpening for clipper blades, knives, scissors, and tools in the Madison Wisconsin and Sun Prairie area.

For more information or to read reviews, Google Sharp On Sight knife sharpening Madison WI.