#onepe

New Dhamaka – Best Earning App

*💥FREE FREE FREE FREE💥* #Onepe Onepe Onepe Onepe *(NOTE👉अभी ओल इन्डिया मे सिर्फ 50,000+लोग जोइन हो चुके हैं टीम बनाकर टोप लिडर बन जाऐ* *🌈TODAY LAUNCH🌈* *🏵Onepe Same OneAD🏵*

*👉12 Level Income* *👉Daily Payment Bank/Paytm* *👉Minimum Redeem ₹3.5 Rs*

*✅10 level income Ka Calculation* 🦠🦠🦠🦠🦠🦠🦠🦠🦠🦠🦠 *Jise karna ho to kar sakta hai* Levels. Members. Monthly Level-1. 6. 24₹👈 Level-2. 36. 72₹👈 Level-3. 216.…

OnePe Me Work Kya Hai

Onepe में क्या वर्क हे ?

1.अपने रेफेर लिंक से कम से कम 20 लोगो को ये अप्प इनस्टॉल करवाये।

2.अपना एक व्हाट्सएप्प ट्रेनिंग ग्रुप बनाये और इन 20 लोगो को ऐड कीजिये।

3.ये बहुत जरुरी है :- 24 घंटे में सिर्फ 2 मिनट के लिए Onepe को ओपन कर ले और 20 लोगो को भी ओपन करवाना जरुरी हे।

(नॉट:- अगर आप या आपकी टीम OnePe को ओपन नहीं करती तो आपको पैसा नहीं मिलेगा।)

📢अगर टीम बनाकर हजारो रू की ईनकम करना चाहते हैं तो…

The Code

I jotted up a quick and simple simulation to read the outputs of the array to make sure that the mistakes I saw on the board were not caused by the design, but by me. It looks to me like the PE is working just fine.

The Simulation Results

I changed up the testing code from last week's attempt at proving PE functionality. Here are the visuals:

System Description

The DataPath module contains the PE and SSRs. It is fed every cycle by an InstructionIssuer which contains an Instruction Memory. The left and right outputs of the PE array are then fed to the OutputMemory. Either the left or right output is then displayed on the LEDs, based on the READ_L switch value.

System Schematic

Instruction Memory Contents

The program on the test architecture is a counter, which should wrap-around at 30.

nop addzz L0 add   L0, L0, #1 add   L0, L0, #1 ; ...

Results

Check out the next post for a video demo of the counter mostly working. :P

One PE Working … mostly.

I think the errors are due to how I wired things, especially since the CLK signal is wired to the down button (PlanAhead complained about that...), but I need to make sure of it. A simple simulator could confirm this.

Code

Here's a synthesizable project with one PE and 2 SSRs. Unfortunately, it is really hard to get the synthesis tool, in this case XST, to not optimize away a few signals and functionality, but I was able to synthesize the following using the new and improved BRAM custom IPs I wrote for the SSRs and the SRAM. I also made a small 4-instruction memory so that the instruction signal as well as others that depended on it wouldn't get optimized away. Here's what I have so far, but there's still work to be done tomorrow.

Schematics