how to take apart Xbox one controller with these steps
Have you been able to kneel before the red ring with fear of death? Would you like to make Microsoft highly manic? Then, how to take apart Xbox one controller more amazing through the charm of modding. If you have enough tolerance and courage to zero your guarantee, then read the guidelines.
Read through the article and you will find out how to take apart Xbox One Controller.
Step 1: Move the faceplate flip around the Xbox One controller. Then, keep your finger in the gap and drag it forward. A decent bridge would be necessary. Step 2: Empty the flame of a low flame Xbox One Controller has six tabs. The tab has covered the cover behind the venting gap on the white side that catches this piece. Pop up each tab alternately, using your case opening equipment or a little screwdriver. Then, gradually clear the lower frame broil. Start at the front end. The faceplate is located on the front end of the device. Step 3: Exclude the Upper Grill In the first place, drag the hard drive that you are not yet shutting down. You will see that there is no flame on this side. You should pop two tabs that are located on the first edge. Pop two tabs at that point which are clear on the sides, much like the flame broil One of the elastic feet covers the last tab. There is a seal in this tab, which will show Microsoft that you have broken your warranty. When you go, it will be a good place to get a handle on the flame brill to lift it. Step 4: Open the two Gap tab areas These two tabs with power plugs. They are most likely in the meantime. This is the point on which you will need to take advantage of the other small screwdriver. Open tab using both screwdrivers or case opening instrument. Finally, start opening the shell. Step 5: Open the five Gap Tab Segments On the opposite side of that side, you will see more than five zones of these tabs. In return, each one of them pops in. Try to keep a steady weight while you open the shell. In addition, you can use case instrument to open them at the same time. Step 6: Open the shell to move a controller around the Xbox One to take a gander on the front end. Find the strut towards the near end of the DVD drive. You can open it with a decent arrangement of your nails and prying. Also, you can open the shell using a flathead screwdriver. There should be four tabs on this side, which you can take alternately. Step 7: Opening the Inquired packaging With the closed shell, you should now have the ability to see the internal packaging. Open the cover board and open it. Then, on the other side, start Xbox and draw the rest of the shell to highlight incoming sections. Step 8: Extract Tenderly to DVD Drives The links that are added to the DVD drive are extremely sensitive. So, first remove this segment with care. Then, just raise it sufficiently to bring it up to the link, and after that, tenderly exclude two. You can flash the DVD drive through a complex modding process. Modifying is necessary if something breaks. If Microsoft detects such a modifying, then it will give your lifetime restrictions from Xbox Live. Step 9: Fly Fan Out In the first place, lift the plastic area. The fan can be pulled out below, yet additional links are connected. So, take him out before the fan is taken out. Step 10: Empty the ring light Ring control is easily available for modification or repair when the case is open in this way. Step 11: Access the motherboard the motherboard will now be instantly clear and open in the same way. You can deliberately pull it in the center of silver boxes or install it. By emptying the motherboard, you may be able to rearrange heatsink by welding again. This will allow the same way you use for programming or firmware mod. Just remember that these are exceptionally mind-boggling forms. Also, you can be banned by Microsoft to illegally release the motherboard. Step 12: Modulate the hard disk drive Despite the fact that it is not located in the basic case, you can open the hard plate drive similarly. Present the drive with more storage rooms. Finally, complete the modifying by removing the majority of the pieces, and sliding it out of the sound. Now it is pressed with another hard drive because the links used are standard. Last word The Xbox One controller is an excellent gaming device. Apart from this, you can make yourself more excellent by adding it to the magic of modding. Again, to paint it or to clean it, you may need to separate the part of this device. Here, I have discussed ways to differentiate the Xbox One Controller. Read it well and you will easily be able to separate your Xbox One controller. Enjoy your game. Read the full article
