#evems

Introduction

Electric vehicles, or EVs, are drastically changing how people travel across the world. Over 16.5 million EVs were in use globally by the end of 2021, a fourfold increase from 2018. This rapid expansion signifies a significant change in the direction of sustainable mobility. However, when more EVs are connected to the grid, new issues with energy demand, grid stability, and infrastructural preparedness are also brought about.

EV Energy Management System (EVEMS) have become vital instruments to facilitate this shift. In addition to maximising EV charging, these intelligent technologies are facilitating resource sustainability, grid balance, and economical energy consumption. The significance, capabilities, advantages, and prospects of EVEMS will be discussed in this blog, along with how businesses such as Dorleco are spearheading the transition to a more intelligent EV ecosystem.

The Development of EVs and How They Affect Energy Demand

Global electricity usage is being greatly impacted by the explosion in EV adoption. By 2030, 4–10% of peak-time electricity demand may come from EV charging, according to the International Energy Agency’s Global EV Outlook 2020. Global energy systems face both opportunity and difficulty because of this rising demand.

The majority of EVs spend roughly 95% of their time parked, which indicates a discrepancy between charging habits and energy consumption patterns. This makes controlling how, when, and where EVs take power imperative.

In affluent countries such as Canada, where EV use is rapidly increasing, this mismatch becomes especially noticeable in residential districts and mixed-use buildings. Demands for charging could overwhelm local networks and raise operating costs if energy management is not done intelligently.

Restrictions to the Broad Adoption of EVs

EVs confront several major obstacles that prevent widespread adoption, despite their advantages for the environment and technological advancements:

1. Inadequate Infrastructure for Charging

Access to dependable charging stations is still a big problem, particularly in underdeveloped urban or rural locations. Many prospective EV purchasers are still put off by range anxiety, or the worry that they won’t have access to nearby charging stations when their battery runs out.

2. Risks of Grid Overload

Rapid growth in EV charging can significantly strain local and regional power networks, especially during peak hours. Blackouts, higher utility bills, and decreased system dependability may result from this.

3. Reliance on Minerals from Rare Earth

Minerals like nickel, cobalt, and lithium are essential to EV batteries. The supply chain is under strain because to growing worldwide demand, which raises questions regarding price volatility, ethical sourcing, and environmental effects. The production of EVs may encounter significant obstacles if these resources are not used and recycled effectively.

EV Energy Management Systems’ (EVEMS) Function

EV Energy Management System provides a potent remedy for these issues. These technologies optimize energy consumption, enhance charging efficiency, and promote sustainable infrastructure development through the use of data analytics, artificial intelligence, and smart grid integration.

Let’s examine the ways in which EV Energy Management System are changing the EV ecosystem:

1. Improving the Infrastructure for Charging

Effective use of the current infrastructure is guaranteed by smart energy management. To plan to charge as efficiently as possible, EV Energy Management System keeps an eye on variables including energy prices, the availability of renewable energy, and customer demand.

These systems are capable of:

Minimize the need for expensive upgrades

Increase the number of charging stations available

Use mobile apps to deliver real-time charging status notifications.

Reduce downtime for charging

2. Maintaining Grid Stability while Balancing Load

In grid load balancing, EVEMS are essential. They aid in flattening peak demand curves and enabling more equitable energy distribution by synchronizing charge schedules.

An EVEMS might, for example, schedule:

charging at night, when there is less demand on the grid

When solar energy is plentiful in the afternoon, charging

In addition to preventing grid overload, this strategy promotes the use of renewable energy, which lessens dependency on fossil fuels and increases grid resilience overall.

3. Battery Recycling and Monitoring

The performance and sustainability of EVs are largely dependent on their batteries. EV Energy Management System assistance:

Check the condition of the battery.

Increase battery life by controlling ideal charging circumstances.

Find early indicators of battery deterioration and notify consumers about them.

Additionally, by tracking battery lifecycle data, EVEMS can help ensure that scarce elements like cobalt and lithium are recycled effectively. This promotes a circular economy and lessens the impact on the environment.

EVEMS’s advantages for customers

EVEMS provide immediate, palpable advantages to individual EV owners in addition to addressing more general systemic issues.

1. Comprehensive Analysis and Insights

EVEMS platforms provide consumers with comprehensive information on:

Driving behaviours

Behaviour of charging

Use of energy

Actionable suggestions, such as when to charge during off-peak hours to save money and enhance battery health, are offered by apps like Tesla’s energy dashboard.

2. Economic Savings

Electricity expenditures are greatly decreased by energy management and intelligent scheduling. EV Energy Management System maximizes cost-efficiency by charging during low-rate hours and reducing energy waste.

Improved User Experience

EVEMS provides a smooth experience with its user-friendly apps and intelligent scheduling:

Personalized pricing schedules based on daily driving requirements

Alerts about nearby charging stations that are available

Optimizing routes for longer trips

Consequently, this ease of use enhances customer satisfaction and further encourages the broader adoption of EVs.

3. Longer Battery Life

EVEMS offers individualized maintenance advice by evaluating real-time data, including charging temperature and frequency. By taking a proactive stance, wear and tear is reduced, early battery replacement is less necessary, and long-term ownership expenses are decreased.

Connecting EVs, Power Grids, and Charging Networks

Indeed, the integration of EVEMS throughout the energy economy represents perhaps their most revolutionary potential. Specifically, these systems enable two-way communication between electric vehicles, charging infrastructure, and the power grid, paving the way for a more intelligent and responsive energy ecosystem.

EVs

Stations for charging

Utility companies

This synchronization makes it possible to:

Dynamic pricing encourages customers to buy at off-peak hours.

Managing loads and striking a balance between local energy supply and demand

Real-time routing minimizes needless detours and assists cars in avoiding crowded stations.

As a result, EVEMS improve transportation’s intelligence and responsiveness to energy realities while also making it cleaner.

Reducing Reliance on Rare Earth Minerals

In response to the growing international concern over the environmental cost of mineral extraction, EVEMS offers a novel approach. By extending battery life and enabling efficient recycling, these solutions significantly reduce the need for continuous raw material extraction.

Mining of new raw materials

High-impact, high-cost production methods

In order to promote a more sustainable product lifespan for EV components, EVEMS also instruct users on appropriate disposal and recycling procedures.

Important Things to Think About When Implementing EVEMS

To that end, a few elements are crucial for governments, corporations, and real estate developers wishing to implement EVEMS (Electric Vehicle Energy Management Systems):

1. Evaluation of Current Infrastructure

Therefore, successful integration depends on insights into hardware, usage patterns, and the available electrical infrastructure.

2. Compatibility

As a result, achieving smooth functionality requires system interoperability across different vehicle models, charging stations, and utility infrastructures.

3. The ability to scale

Given the anticipated significant increase in EV usage, the design team needs to create EVEMS with scalability in mind, both in terms of hardware and software capabilities.

4. Security of Cyberspace

Robust security protocols are essential to safeguard privacy and stop cyberattacks since EVEMS gather and send sensitive user and grid data.

Leading the Way: Dorleco’s Contribution to EVEMS Innovation

In line with the evolving demands of electric mobility, and furthermore, as part of our ongoing mission to drive innovation, Dorleco remains steadfast in its commitment to transforming the EV experience through cutting-edge solutions.

VCUs, or smart vehicle control units

Keypads and CAN Displays

Personalized EV Software Services

Our technological advancements allow:

Effective use of energy

Improved infrastructure for charging

Dependable integration of the gridAt Dorleco, we promote more seamless EV adoption across the fleet, commercial, and residential sectors by placing a strong emphasis on sustainability, user experience, and innovation. Consequently, by addressing challenges such as grid overload, enhancing energy efficiency, and improving system interoperability, we are actively contributing to the development of a more intelligent and environmentally friendly future for electric mobility.

Conclusion:

Electric cars are becoming an essential part of global sustainability initiatives, not just a passing fad. However, we require intelligent systems that can control energy, guarantee efficiency, and adjust to change to support the EV revolution.

The foundation of this change is EV Energy Management Systems (EVEMS). EVEMS are essential to achieving the full potential of electric mobility, from empowering customers and lowering resource dependency to stabilizing grids and optimizing batteries.

As a result, the goal of a cleaner, smarter, and more connected transportation future is becoming closer to reality, especially as businesses like Dorleco continue to drive innovation.

March 5, 2024

 by dorleco

with no comment

 Autonomous Vehicle Technology

Edit

Introduction

In the United States, internal combustion engines power almost 250 million highway vehicles due to their exceptional longevity and drivability. They can run on renewable or alternative fuels in addition to gasoline or diesel (e.g., natural gas, propane, biodiesel, or ethanol). Additionally, they can be paired with plug-in hybrid electric systems to increase the range of hybrid electric vehicles or with hybrid electric powertrains to improve fuel efficiency.

Internal combustion engines are divided into two groups:

Continuous combustion:

Engines with both intermittent and continuous combustion. Fuel and oxidizer enter the engine steadily, which is the hallmark of a continuous-combustion engine. An engine (such as a jet engine) maintains a steady flame.

Intermittent-combustion engines:

The air and fuel in an intermittent combustion engine ignite periodically, giving rise to the term “reciprocating engine.” A cycle is used to process discrete amounts of fuel and air. Examples of this second type are diesel engines and gasoline piston engines.

A sequence of thermodynamic events can be used to describe internal combustion engines. Thermodynamic processes take place concurrently in a continuous-combustion engine as the fuel, oxidizer, and combustion products move through the engine in a steady flow.

In contrast, all of the events in an intermittent combustion engine happen one after the other and are repeated throughout each cycle.

Internal combustion engines consume air, compress it, and either introduce fuel into the air or compress the air-fuel combination. Rockets are an exception to this rule, as they use both liquid-propellant and solid rocket motors.

The air-fuel mixture is then burned, work is obtained from the expansion of the hot gaseous combustion products, and finally, the combustion products are discharged through the exhaust system, as is the case with all internal combustion engines.

Their functioning can be compared to that of external combustion engines (such as steam engines), where energy is obtained exclusively by heat transfer to the working fluid via a heat exchanger and no chemical reaction occurs in the working fluid.

The four-stroke, gasoline-powered, homogeneous-charge, spark-ignition engine is the most widely used internal combustion engine. This might be attributed to its exceptional performance as a leading player in the ground transportation sector.

The aeronautics industry uses spark-ignition engines as well, but because of its focus on range, speed, and passenger comfort, aircraft gas turbines have emerged as the industry’s main players.

Exotic systems including advanced rocket engines and motors, like those found on U.S. space shuttles and other spacecraft, and supersonic combustion ramjet engines (scramjets), like those envisioned for hypersonic aircraft, are also included in the category of internal combustion engines.

How Does An Internal Combustion Engine Work?

The fundamental chemical process of releasing energy from a fuel and air mixture is called combustion, or burning. The process of fuel ignition and combustion in an internal combustion engine (ICE) takes place inside the engine. After that, the engine uses a portion of the energy produced by combustion to power itself. A stationary cylinder and a moving piston make up the engine. The crankshaft rotates as a result of the piston being pushed by the expanding combustion gasses. In the end, this action turns the wheels of the car through a set of gears in the powertrain.

The spark-ignition gasoline engine and the compression-ignition diesel engine are the two types of internal combustion engines that are currently in production. The majority of these are four-stroke engines, which require four piston strokes to complete a cycle. The intake, compression, combustion, power stroke, and exhaust are the four independent operations that make up the cycle.

The methods used by compression ignition diesel engines and spark ignition gasoline engines to feed and ignite fuel are different. During the intake phase in a spark ignition engine, fuel and air are combined and then forced into the cylinder. The fuel-air mixture is compressed by the piston and then ignited by the spark, leading to combustion. During the power stroke, the piston is pushed by the combustion gasses’ expansion. Only air is introduced and subsequently compressed into an engine in a diesel. The fuel then ignites when diesel engines spray it into the hot compressed air at a proper, controlled rate.

In essence, an internal combustion engine converts the air-fuel mixture’s heat energy into mechanical energy. The reason it is named Four Strokes is that a full combustion cycle in the piston requires four strokes to complete. An internal combustion engine, sometimes known as an ICE (internal combustion engine), is a four-stroke piston engine that powers a passenger car.

Let’s now investigate which constitutes an ICE’s principal parts.

The camshaft(s), valves, valve buckets, valve return springs, spark/glow plugs, and injectors (for direct injection engines) are typically located in the cylinder head. The engine’s cooling liquid passes via the cylinder head.

We can locate the piston, connecting rod, and crankshaft inside the engine block. Regarding the cylinder head, coolant passes through the engine block to assist in regulating the engine’s temperature.

From BDC to TDC, the piston travels inside the cylinder. When the piston is near TDC, a volume is formed between the cylinder head, engine block, and piston. This space is known as the combustion chamber.

An ICE with four strokes has the following phases (strokes) in a complete engine cycle:

Intake power (expansion) exhaust compression intake The piston’s movement between the bottom and top dead centers is referred to as a stroke.

Now that we are aware of an ICE’s constituent parts, we can investigate the actions that take place throughout each engine cycle stroke. The position of the piston at the start of each stroke and the specifics of what happens inside the cylinder are displayed in the table below.

Stroke 1 – INTAKE

Stroke 2 – COMPRESSION

 After the intake stroke is complete, the piston begins the compression stroke at BDC. The intake and exhaust valves close during the compression stroke, and the piston travels toward TDC. The air/mixture is compressed when both valves are closed, and when the piston approaches TDC, the pressure reaches its maximum. During the compression stroke, just before the piston reaches TDC (but not quite there),

Stroke 3 – POWER

Stroke 4 – EXHAUST

After the power stroke is over, the exhaust stroke begins with the piston at the BDC. There is an open exhaust valve during this stroke. Most of the exhaust gasses are forced out of the cylinder and into the exhaust pipes by the piston’s movement from the BDC to the TDC. The engine uses energy during the exhaust stroke because the components’ inertia causes the crankshaft to rotate.

As you can see, the piston needs to make four strokes to complete a combustion (engine) cycle. This indicates that two full crankshaft revolutions (720°) are required for one engine cycle.

Advantages of internal combustion engines

Engine size is extremely small in comparison to external combustion engines.

The power-to-weight ratio is elevated.

Excellent for applications with low power requirements

Typically, more transportable than external combustion engines of the same kind

safer to use with a much shorter start time

Higher efficiency compared to an external combustion engine

There is no possibility of working fluid leaks minimal upkeep is necessary

Compared to external combustion engines, there is a reduction in lubricant use.

Because the peak temperature is only achieved briefly (during the fuel’s explosion), the overall working temperature in the case of reciprocating internal combustion is modest.

Disadvantages of internal combustion engines

The range of fuels available for utilization is restricted to extremely high-quality gaseous and liquid fuels.

Fuel utilized, such as gasoline or diesel, is quite expensive.

In general, engine emissions are higher than those of an external combustion engine.

Unsuitable for producing significant amounts of power When there is reciprocating internal combustion, fuel detonation produces noise.

Types and applications of internal combustion engine:

Gasoline engines are utilized in automobiles, boats, and airplanes.

Gas engines are employed to provide industrial power.

Diesel engines are utilized in the automotive, railroad, power, and marine industries.

Gas turbines: They are employed in the maritime, industrial, and aircraft industries.

Conclusion:

To sum up, for more than a century, internal combustion engines have been essential in powering a variety of industry and transportation options. They are essential to contemporary industrialization and mobility because of their effectiveness, dependability, and flexibility. However, the desire to switch to greener, more sustainable options is growing as worries about the effects on the environment and the depletion of resources increase.

Internal combustion engines’ dependence on fossil fuels is still a severe disadvantage, despite notable improvements in efficiency and emissions reduction. Research and development efforts are being directed toward alternative fuels like biofuels and hydrogen, as well as electrification technologies like electric and hybrid powertrains, in an attempt to address these problems.

Moreover, the use of sophisticated engine management systems, lightweight materials, and enhanced aerodynamics keeps improving internal combustion engine performance and fuel efficiency. To combat climate change and lessen reliance on limited resources, a thorough transition to greener transportation options is required.

In conclusion, even though internal combustion engines have proved essential to contemporary transportation and industry, there are growing concerns about their long-term viability. The key to the future is adopting cutting-edge technologies that balance environmental protection with the changing demands of society for dependable and efficient power sources.

March 1, 2024

 by dorleco

with no comment

 Control Systems

Introduction

Sales of electric automobiles are rising. By the end of 2021, there will be over 16.5 million electric vehicles on the road worldwide, which is quadruple the number from 2018.

EVs also bring with them an increasing electricity demand. According to the 2020 International Energy Agency’s Global EV Outlook, during periods of peak demand, the percentage of electricity used for EV charging might reach as high as 4–10% by 2030.

However, the majority of cars—EVs included—are parked for approximately 95% of the time. In addition, there are times during the day when the peak demand for power varies dramatically, resulting in periods of unused production capacity.

Managing electrical capacity when maintaining charging stations has become more difficult as electric vehicles have grown in popularity in Canada, particularly in multi-use residential and commercial buildings.

Although a lot of companies are installing EV charging stations to accommodate their clients, employees, and tenants, there’s a chance that the whole load will surpass the energy capacity. EV energy management systems (EVEMS) can help with it.

Challenges to the widespread adoption of EVs

1. Inadequate infrastructure for charging

The broad adoption of electric vehicles is severely hampered by the inadequate infrastructure for charging them. This is especially true in less developed or rural locations, where there are fewer charging stations, deterring drivers from switching to electric cars.

Range anxiety is also brought on by a lack of charging infrastructure, since drivers may worry that they won’t be able to locate a charging station when traveling long distances.

2. Overloaded electrical grids

The possibility of grid overloading is another obstacle to the widespread use of electric vehicles. The demand for power rises as more and more electric vehicles are connected to the grid, increasing the risk of grid overloading at times of peak demand.

This can therefore lead to problems such as blackouts and other problems that could harm the electricity system’s dependability.

3. Insufficient availability of vital minerals

The insufficient availability of vital minerals and rare earth metals required for electric vehicle infrastructure is a significant obstacle to the extensive integration of electric vehicles.

These minerals are needed to produce EV batteries and other necessary parts. However as the number of EVs on the road rises, demand for certain minerals is rising quickly, and the supply of these minerals is restricted globally.

This might cause problems for EV producers in the supply chain and increase their costs, which would hinder the uptake of electric vehicles.

How smart Energy Management System can help overcome these challenges?

This is how smart EV energy management systems can help one overcome the above challenges.

1. Utilize charging infrastructure effectively

By making efficient use of the current infrastructure, smart energy management systems might potentially address the issue of insufficient charging infrastructure.

These systems can maximize charging station utilization while minimizing their impact on the power grid by analyzing energy consumption, renewable energy generation, and energy costs.

This can facilitate the mass adoption of electric vehicles by reducing the need for costly infrastructure upgrades and improving the accessibility and dependability of the charging infrastructure.

To further improve the effectiveness of the charging infrastructure, electric vehicle drivers can also receive real-time information about the location and availability of charging stations by using mobile apps and EV energy management software.

2. Load balancing to prevent excessive load on the grid

Potentially, smart energy management technologies can help with grid overload issues. By coordinating the charging of loads to occur during off-peak hours, when there is less power demand, these sophisticated systems can distribute the load on the grid.

Smart energy management systems can increase grid stability and dependability by employing this technique to keep the grid from suffering extra demand during peak times.

Moreover, by utilizing energy produced during off-peak hours, when renewable sources like solar and wind power are more plentiful, this technique can maximize the usage of renewable energy sources.

Battery monitoring and recycling to reduce the carbon footprint of EVs To reduce the carbon footprint of electric vehicles (EVs), battery recycling and surveillance are essential.

By gathering vital information on battery health and consumption statistics, intelligent energy management systems may dramatically maximize the efficiency of electric vehicle batteries.

Moreover, intelligent energy management systems can guarantee that batteries are properly recycled at the end of their useful lives, reducing the environmental impact of electric vehicles.

This entails decreasing the need for mining, recovering vital components and rare earth metals required in battery production, and lowering the carbon footprint associated with battery production.

3. For EVs, why should you choose a smart Energy Management System app?

An intelligent energy management app for electric vehicles (EVs) maximizes energy use, which lowers costs and boosts sustainability and efficiency.

It enables EV owners to control several energy-related aspects of their cars, such as battery consumption and charging duration.

4. Detailed user analytics

One of the main advantages of the smart EV app for energy management is the availability of thorough data. Analyzing and tracking a user’s energy consumption patterns can be made easier with the help of a smart EV energy management system.

In turn, this can help owners of electric vehicles (EVs) identify inefficient locations and make data-driven choices to maximize their energy use.

EV owners can obtain a thorough insight into their energy consumption, charging history, and driving trends by applying extensive user statistics, like those offered by the Tesla application.

Furthermore, tailored suggestions can be provided to enhance energy efficiency, such as cutting back on energy use during peak hours and timing charging to prevent needless energy loss.

By putting these suggestions into practice, the EV’s range may be increased and driving enjoyment may be enhanced overall.

5. Cost savings

An intelligent EV energy management system can help owners of electric vehicles (EVs) reduce their charging costs and hence improve their overall cost-effectiveness by maximizing energy use.

As an example, a powerful EV smart energy management system may identify charging infrastructure inefficiencies and continuously monitor charging operations in real time.

This information can help EV owners minimize energy loss and associated costs by helping them make informed decisions about when and how to charge their cars.

6. Improved experience for users

EVs offer several advantages for energy management, including better user experience. Developing a strong EV energy management system can greatly improve the experience for the final user.

First off, owners of electric vehicles can monitor and control their charging sessions with ease thanks to the user-friendly interface provided by EV energy management software, which increases convenience and flexibility.

For example, the EV energy management software can provide customized charging schedules according to the user’s driving habits and preferences, making charging smooth and enjoyable.

EV owners may also make informed decisions about their energy usage and its ecological impact by using the EV energy management system, which can offer them insights into their energy consumption and carbon footprint.

7. Enhances synchronization

A robust energy management platform designed for electric vehicles (EVs) can improve communication between power grids, EV drivers, and the charging infrastructure.

With the help of the EV smart energy management application, drivers of electric vehicles may plan the most efficient routes and steer clear of needless detours by accessing real-time information about the availability and status of charging stations.

Additionally, by enabling two-way communication between EV drivers and power grids, the EV energy management program can improve the synchronization of energy supply and demand.

The program ensures that electricity demands stay balanced and maintains grid stability by adjusting the billing rate based on the available capacity of the grid.

Additionally, by encouraging EV drivers to charge their cars during off-peak hours, the EV energy management platform can help reduce peak demand, ease grid stress, and lessen the chance of blackouts.

8. Reduction in consumption of essential elements

An intelligent energy management app for electric vehicle owners can optimize their energy usage and offer tools to prolong the life of the battery and check its condition.

The energy management software for EVs monitors temperature, charging habits, and battery usage to help identify potential problems and make recommendations for enhancing battery performance.

As a result, the software can aid in lowering the need for new EV batteries as well as the amount of rare earth materials needed to produce them.

The EV energy management system can also offer information on battery recycling and disposal, which is essential for minimizing environmental effects.

Factors to consider while implementing an effective smart Energy Management System

Have an awareness of the current state

Integration and interoperability

Choosing the right hardware and software

Scalability

Managing cyber risk

Conclusion:

The importance, difficulties, and potential applications of electric vehicle (EV) energy management systems (EMS) would be summarized as follows:

An important step forward in the integration of electric vehicles into our transportation infrastructure is the use of electric vehicle energy management systems.

These technologies are essential for maximizing energy efficiency, enhancing car performance, and guaranteeing effective charging procedures.

Electricity flow between the grid, EVs, and charging stations is intelligently managed by EMS, which improves user experience while simultaneously supporting the sustainability and stability of the power system.

The requirement for standardization and interoperability among the many parts and stakeholders in the EV ecosystem is one of the main issues facing EV EMS.

For EMS to be widely used and effective, it must be possible for various charging networks, car manufacturers, and energy providers to communicate and work together seamlessly.

Furthermore, EMS has both opportunities and challenges as a result of the quick development of EV technology and the breakthroughs made in renewable energy sources.

Adding projections for renewable energy supply, dynamic pricing models and changes in grid demand to EMS algorithms can improve their flexibility and effectiveness.

Looking ahead, to overcome these obstacles and realize the full potential of EV Energy Management Systems, more research and development work will be required.

Innovation, standardization, and scalability of EMS solutions will be driven by collaboration between industry actors, governments, and researchers.