#electrolube

SGB (2X Grease) was developed as an extension of the No 2 Range (SFA, SGA and SOA) with increased plastics compatibility. This product development was necessary due to the use of thermoplastics in the electronics and automotive industries. SGB will significantly increase contact performance and lifetime. Separate data sheets are available for the diluted oil (EML), oil (SOB), the red standard grease (SGBR) and the low penetration grease (SGBH).

Key Product Features & Benefits

High quality, non-melting contact grease

Hard consistency version SGBH) and oil version (SOB)

Reduces contact wear and arcing

Good plastics compatibility

Product Description

UAT Universal Acrylic Conformal Coating Thinners is a high purity solvent blend designed for use with all Electrolube acrylic based coatings. Electrolube coatings suitable for use with UAT are:

HPA – High Performance Acrylic APL – Acrylic Protective Lacquer TRV – Tropicalised Varnish

The primary use of UAT is to dilute coatings for use in dip and spray coating applications however it can be used to clean coating equipment which has been used with the above coatings.

For the correct mix ratios please refer to the TDS.

Key properties

Used to dilute acrylic conformal coatings for use in dipping and spraying applications

Thermal Management of Electronics - Webinar

In this comprehensive Thermal Management webinar, Global Technical Support Manager Jade Bridges examines a wealth of material including the basics of thermal conductivity measurement, TIM options, application methods, silicones versus non-silicones, gap fillers and phase change materials. Some real life case studies examining problems and solutions are included in the webinar.

Key takeaways:

1)      Understand the importance of thermal management

2)      Learn how to assess the options available and make a considered choice (for example, silicone, non-silicone, greases, thermal gap pads, phase change materials, thermally conductive putty and gap fillers)

3)      Gain a clear understanding of bond line thickness

4)      The importance of application methods

New Post has been published on http://engineer.city/defence-mechanism/

Defence mechanism

Designing protection solutions for wearable devices. By Karen L Harrison

One of the biggest challenges posed when designing a wearable device lies in the environment where the technology will primarily be used. For example, a temperature sensor on a static device will have to withstand temperatures within that environment and any thermal shock or cycling that may take place. However, a temperature sensor in a wearable device has the added consideration of physical interactions. The device will be moved, worn, may see impact, may be flexed and potentially exposed to a number of additional elements, such as water or chemicals, for example. It is therefore imperative that these devices are protected accordingly to ensure reliable performance when utilised in their end-use environments.

Effective protection can be provided in the form of encapsulation resins or conformal coatings but with so many potential applications, this can also generate another challenge in selecting the most suitable protection compound. The wearable device is likely to use some form of connectivity, whether it be direct to another device or system or via a sensor to record changes in information gathered. This connection to other devices will operate via radio waves, consequently any protection compound used, must allow RF signals to be transmitted without any interference.

With the increasing diversity of wearable devices will come a vast array of requirements, which will define the need for appropriate and reliable protection solutions. It is clear that every application will have its own criteria in terms of performance, environment and expected use and in all cases, a reliable and accurate response is required from the wearable device.

Protective solutions currently available from Electrolube for wearable device designers include UR5041, a two-part, ultra high performance resin system, that features excellent resistance to seawater and low water absorption. Suitable for use down to -60°C with good low-temperature performance, the resin provides high toughness, tear resistance, oxidation resistance and delivers high performance in a wide range of challenging environments, particularly in marine environments.

The transparent AFA conformal coating is ideal for applications where LEDs and displays are involved, providing excellent clarity, UV resistance and exceptional protection in humid and salt-mist environments.

HTCX is a smooth, silicone-free thermal paste that provides exceptionally high thermal conductivity, lower oil bleed and lower evaporation weight loss. The new paste is also highly resistant to humidity and thermal cycling and is recommended where efficient and reliable thermal coupling of electrical and electronic components is required, and between any surface where thermal conductivity and heat dissipation is important.

UR5634 is a two-part, semi-rigid, optically clear polyurethane resin that achieves a water-white transparency, ideal for applications that require LED potting. This low-hazard material is weather resistant, impervious to acids/alkalis and is strongly resistant to yellowing when exposed to UV light – of particular benefit to devices exposed to direct sunlight.

By working through complex device parameters with an electro-chemicals manufacturer, it is possible to quickly find the most suitable solution for the application and ensure the performance of the wearable device during its working life.

For more information, visit www.engineerlive/ede

Karen L. Harrison is with Electrolube (a division of HK Wentworth). 

Images: