Oct 2, 2016
בסוף מתרגלים להכל❤️ #דודוטסה #boombox3 #היה_טוב_וטוב_שהיה (at פארק נחל חדרה)
Loading...
seen from United States
seen from United States
seen from United States
seen from Hong Kong SAR China
seen from United States
seen from United States
seen from China
seen from China
seen from United States
seen from United States
seen from United States
seen from Brazil
seen from France
seen from United States
seen from United States
seen from United States
seen from T1
seen from United Kingdom
seen from United States
seen from China
בסוף מתרגלים להכל❤️ #דודוטסה #boombox3 #היה_טוב_וטוב_שהיה (at פארק נחל חדרה)
Anya is live and ready to show you everything. Watch her strip, dance, and perform exclusive shows just for you. Interact in real-time and make your fantasies come true.
Free to watch • No registration required • HD streaming
I’ve had two major setbacks. One) I blew out one of the amps somehow, and now i only have one leaving my speaker set up non-functional.
Two) The right side isnt responsive always, and thus i may have to rewire the entire thing.
Im going to go through the parts I used for this to get a general idea of how much it cost, and how much it would cost if i didnt have access to anything.
(Excuse the poor formatting, ill go back and reformat later)
Subwoofer Pair- Pair Energy 22 Pro Monitor woofer PL9B2 4DR51729 For Sale Free (from E-waste Drive: Found online for $45)
Sony Mid Pair- Free (from E-waste Drive: Found online for $45 each- total 90)
Tweeter Pair- From Discounted Pyle Set. Set New: $103. Estimated cost for pair- $7
Crossover Pair $32
1/4 inch MDF (4 sheets) $20
1/8 inch MDF (1 sheet) $4
Sealed Lead Acid Battery $20
Charge Controller (free-New: $22)
Trumpet Case (free-New: $70)
DPDT Switches (8) (paid $2 for 7 of them and 5 for one- total paid, $19- non-discounted total $40)
Speaker Wire (Had)
Solder (Had)
Adaptaplug 273-350 socket $5
Car Charger 12v 5a adaptaplug (with one M type tip) $8
M type tip $7
M coaxial DC power Jack $4
Assorted Screws and Nuts $10
Epoxy $5
Super Glue Gel (Loctite) (2 tubes) $6
Lepai LP 2020A+ $20 ($32 new)
Female To Female 1/8 jack $5
Male to male 1/8 cable (Had)
Speaker Connectors $19.50
I only have a few parts left to buy, and a few steps to complete.
PIECES TO PURCHASE:
5.5 mm-2.1 mm (TYPE M) DC Panel Mount
Adaptaplug replacement socket
6 Speaker Connectors
1/4 MDF
2 tubes of gel super glue LOCTITE
“M” Type connector
Cost: $31.34
1/8 MDF
Sealed Lead Acid Battery
2 Lepai LP 2020A+
Unnecessary Stuff (but will make it more professional-ish)
Caulk
Epoxy
Brass Plates
STEPS LEFT as of April 28th 2015:
Complete Box, except for the top; Use supports to reinforce dividers, and glue in all dividers.
(Caulk Seams)
Wire for final installation
Cut wire
Solder and heat shrink connections
Wire in switches
Cut Top piece of 1/8 MDF
Glue in top piece
Cut Holes for Speaker Ports in Top
Wire ports
Install ports
Cut hole in side for amp
Cut pieces of MDF for amp securing sides/port housing-audio port, and power port.
Wire electronics
Cut wire
Solder and heat shrink connections
Wire in switches
Cut pieces for switch setting
Install switches
TEST
Seal Box
Purchase/Attach Brass Plates
FINISH
I visited Radioshack today and now i have a pretty good understanding how my power set up would work. I have both a “M” type wall plug (that came with the lepai, 13v at 3 amps), and today i bought an interchangable car plug, that can accept any letter type end. I also bought an “M” type end for that as well, so either i can plug it into the wall, or my car.
For the set up ill need 2 DPDT ON/OFF/ON Switches, another “M” type plug, the plug acceptor (that converts the easy acceptor end into solderable wires), and some wire. The set up will have 3 definite positions. 1) Charge battery, 2) Run from wall/car power and 3) run from battery (with a possible 4th being charge and run from battery simultaneously, if the charge controller will allow it), and these three/four positions will depend on the position of the two switches. Ill also need an “M” type jack which i found here on radioshack, but would prefer to find on amazon.
Anya is live and ready to show you everything. Watch her strip, dance, and perform exclusive shows just for you. Interact in real-time and make your fantasies come true.
Free to watch • No registration required • HD streaming
SO i decided to combine Boombox 3 (trumpet case a.k.a. Louie) and my ampbox. To do this, ill need 6 more DPDT heavy duty ON/OFF/ON Switches, and 6 ports. Assume the system will be symmetrical across R and L. One of each will go inbetween the amp and the crossover, so either i can power the crossover, or a speaker with the full range on each side. Then the other 2 on each side will go inbetween the Crossover and the Mid, and the crossover and the sub, so i can plug in an external mid and/or external sub. Each switch will control them individually so i can urn however many on or off.
DECIDING ON AN AMP:
Currently I need to pick which amp i’m going to use for my boombox. I thought i was going with the ...
Lepai LP-2020A+ for 26.75 (orin 35.00)
however now im looking at both the
Lepai BTL (A6FM-USB) for 16.60 (orig. 50.00) Lepai A68 for 26.90 (orig. 40.00)
If anyone know about the second two let me k now (i already own two of the first but the remote and radio options seem nice, also the power is 12v at 2 amps instead of 13 v at 3 amps.
My PYLE speakers came today. Two 6.5 inch midwoofers, 2 2-way crossovers, and 2 tweeters. I’m using the tweeters in this boombox. This case continues to surprise me with how perfect it fits everything. The tweeters fit EXACTLY underneath the mounted crossovers. There’s barely any tolerance between them.
Previously i had covered the nuts in epoxy to prevent them from turning on their own incase the super glue isn’t strong enough. Also, i glued in nuts over the hole of the crossovers so i can unscrew them from the outside.