MDDN251 Documentation

#include <SPI.h> #include <Dhcp.h> #include <Dns.h> #include <Ethernet.h> #include <EthernetClient.h> #include <Temboo.h> #include "TembooAccount.h" // Contains Temboo account information

#include <Wire.h> // Must include Wire library for I2C #include <SparkFun_MMA8452Q.h> // Includes the SFE_MMA8452Q library

#include <Adafruit_NeoPixel.h> #include <avr/power.h>

#define PIN 7

MMA8452Q accel; // instance of the MMA8452Q

Adafruit_NeoPixel strip = Adafruit_NeoPixel(16, PIN, NEO_GRB + NEO_KHZ800);

int r; int g; int b;

byte ethernetMACAddress[] = ETHERNET_SHIELD_MAC; EthernetClient client;

//limit Temboo calls while testing //int maxCalls = 3;

// The number of times this Choreo has been run so far in this sketch //int calls = 0;

 boolean portraitu = true;  boolean portraitd = true;

void setup() {  Serial.begin(9600);

 // --- pixelring ---//  strip.begin();  //strip.setBrightness(64);  strip.show(); // Initialize all pixels to 'off'  // ---pixelring end ---//

 accel.init(); // initialize accelerometer

 // For debugging, wait until the serial console is connected  delay(4000);

while (!Serial);

// Serial.print("DHCP:");  if (Ethernet.begin(ethernetMACAddress) == 0) {   // Serial.println("FAIL");    while (true);  } // Serial.println("OK");  //delay(5000);

 Serial.println("GO\n"); }

void loop() {

accel.read(); byte pl = accel.readPL();

 if (/*(calls < maxCalls) &&*/ (PORTRAIT_D == pl) && (portraitd == true)) {    //Serial.print("\r");    Serial.println("Wellington");    runGetWeatherWellington();

   //calls++;

   portraitd = false;    portraitu = true;

 }  else if (/*(calls < maxCalls) &&*/ (PORTRAIT_U == pl) && (portraitu == true)) {    //Serial.print("\r");    Serial.println("Munich");

   runGetWeatherMunich();    //calls++;

   portraitd = true;    portraitu = false;

} /*else if (LANDSCAPE_L == pl || LANDSCAPE_R == pl || LOCKOUT == pl){   Serial.println("LED OFF");

}*/ }

//  ---PixelRing fancy wipe---

void colorWipe(uint32_t c, uint8_t wait) {  for (uint16_t i = 0; i < strip.numPixels(); i++) {    strip.setPixelColor(i, c);    strip.show();    delay(wait);  } }

//WEATHER WELLINGTON

void runGetWeatherWellington() {  TembooChoreo GetWeatherByAddressChoreo(client);

 // Set Temboo account credentials  GetWeatherByAddressChoreo.setAccountName(TEMBOO_ACCOUNT);  GetWeatherByAddressChoreo.setAppKeyName(TEMBOO_APP_KEY_NAME);  GetWeatherByAddressChoreo.setAppKey(TEMBOO_APP_KEY);

 // Set Choreo inputs  String UnitsValue = "c";  GetWeatherByAddressChoreo.addInput("Units", UnitsValue);  String AddressValue = "Wellington, NZ"; // Adress here  GetWeatherByAddressChoreo.addInput("Address", AddressValue);  String DayValue = "1"; // 1 = today, 2 = tmr...  GetWeatherByAddressChoreo.addInput("Day", DayValue);  // Identify the Choreo to run  GetWeatherByAddressChoreo.setChoreo("/Library/Yahoo/Weather/GetWeatherByAddress");

 // Run the Choreo  unsigned int returnCode = GetWeatherByAddressChoreo.run();

 // A return code of zero means everything worked  if (returnCode == 0) {    while (GetWeatherByAddressChoreo.available()) {

     String name = GetWeatherByAddressChoreo.readStringUntil('\x1F');      name.trim();

     String data = GetWeatherByAddressChoreo.readStringUntil('\x1E');      data.trim();

     if (name == "Temperature") {        Serial.print(data.toInt()); //print current Temp

       if (data.toInt() <= -10) {          r = 0;          g = 255;          b = 255;        }        // wenn Temperatur zwischen -10 und 5        if (-10 < data.toInt() && data.toInt() <= 5) {          r = 0;          g = 255;          b = 255;          int steps = 0;          for (int i = -10; i < data.toInt(); i++) {            steps++;          }          b = b - (steps * 17);        }        // wenn Temperatur zwischen 5 und 20        if (5 < data.toInt() && data.toInt() <= 20) {          r = 0;          g = 255;          b = 0;          int steps = 0;          for (int i = 5; i < data.toInt(); i++) {            steps++;          }          r = r + (steps * 17);        }        // wenn Temperatur zwischen 20 und 35        if (20 < data.toInt() && data.toInt() <= 35) {          r = 255;          g = 255;          b = 0;          int steps = 0;          for (int i = 20; i < data.toInt(); i++) {            steps++;          }          g = g - (steps * 17);        }        // wenn Temperatur über 35        if (35 < data.toInt()) {          r = 255;          g = 255;          b = 0;        }

       colorWipe(strip.Color(r, g, b), 50);        strip.show();

     }    }

 }

 GetWeatherByAddressChoreo.close(); }

//WEATHER WELLINGTON FIN

//WEATHER MUNICH

void runGetWeatherMunich() {  TembooChoreo GetWeatherByAddressChoreo(client);

 // Set Temboo account credentials  GetWeatherByAddressChoreo.setAccountName(TEMBOO_ACCOUNT);  GetWeatherByAddressChoreo.setAppKeyName(TEMBOO_APP_KEY_NAME);  GetWeatherByAddressChoreo.setAppKey(TEMBOO_APP_KEY);

 // Set Choreo inputs  String UnitsValue = "c";  GetWeatherByAddressChoreo.addInput("Units", UnitsValue);  String AddressValue = "Munich";  GetWeatherByAddressChoreo.addInput("Address", AddressValue);  String DayValue = "1";  GetWeatherByAddressChoreo.addInput("Day", DayValue);  // Identify the Choreo to run  GetWeatherByAddressChoreo.setChoreo("/Library/Yahoo/Weather/GetWeatherByAddress");

 // Run the Choreo  unsigned int returnCode = GetWeatherByAddressChoreo.run();

 // A return code of zero means everything worked  if (returnCode == 0) {    while (GetWeatherByAddressChoreo.available()) {      String name = GetWeatherByAddressChoreo.readStringUntil('\x1F');      name.trim();

     String data = GetWeatherByAddressChoreo.readStringUntil('\x1E');      data.trim();

     if (name == "Temperature") {        Serial.print(data.toInt()); //print current Temp

       if (data.toInt() <= -10) {          r = 0;          g = 255;          b = 255;        }        // wenn Temperatur zwischen -10 und 5        if (-10 < data.toInt() && data.toInt() <= 5) {          r = 0;          g = 255;          b = 255;          int steps = 0;          for (int i = -10; i < data.toInt(); i++) {            steps++;          }          b = b - (steps * 17);        }        // wenn Temperatur zwischen 5 und 20        if (5 < data.toInt() && data.toInt() <= 20) {          r = 0;          g = 255;          b = 0;          int steps = 0;          for (int i = 5; i < data.toInt(); i++) {            steps++;          }          r = r + (steps * 17);        }        // wenn Temperatur zwischen 20 und 35        if (20 < data.toInt() && data.toInt() <= 35) {          r = 255;          g = 255;          b = 0;          int steps = 0;          for (int i = 20; i < data.toInt(); i++) {            steps++;          }          g = g - (steps * 17);        }        // wenn Temperatur über 35        if (35 < data.toInt()) {          r = 255;          g = 255;          b = 0;        }

       colorWipe(strip.Color(r, g, b), 50);        strip.show();

     }    }

 }

 GetWeatherByAddressChoreo.close(); }

https://learn.sparkfun.com/tutorials/mma8452q-accelerometer-breakout-hookup-guide

colourfade:  blue ( = cold ) - green - yellow - orange - red ( = hot )

#include <Adafruit_NeoPixel.h> #include <avr/power.h>

#define PIN 7

// Parameter 1 = number of pixels in strip // Parameter 2 = Arduino pin number (most are valid) // Parameter 3 = pixel type flags, add together as needed: //   NEO_KHZ800  800 KHz bitstream (most NeoPixel products w/WS2812 LEDs) //   NEO_KHZ400  400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers) //   NEO_GRB     Pixels are wired for GRB bitstream (most NeoPixel products) //   NEO_RGB     Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2) Adafruit_NeoPixel strip = Adafruit_NeoPixel(16, PIN, NEO_GRB + NEO_KHZ800);

int r; int g; int b; int celsius = 28; //set the temperature manually

void setup() {

 Serial.begin(9600);

 strip.begin();  strip.setBrightness(64);  strip.show(); // Initialize all pixels to 'off'

}

void loop() {

 // wenn Temperatur kleiner als -10  if (celsius <= -10) {    r = 0;    g = 255;    b = 255;  }  // wenn Temperatur zwischen -10 und 5  if (-10 < celsius && celsius <= 5) {    r = 0;    g = 255;    b = 255;    int steps = 0;    for (int i = -10; i < celsius; i++) {      steps++;    }    b = b - (steps * 17);  }  // wenn Temperatur zwischen 5 und 20  if (5 < celsius && celsius <= 20) {    r = 0;    g = 255;    b = 0;    int steps = 0;    for (int i = 5; i < celsius; i++) {      steps++;    }    r = r + (steps * 17);  }  // wenn Temperatur zwischen 20 und 35  if (20 < celsius && celsius <= 35) {    r = 255;    g = 255;    b = 0;    int steps = 0;    for (int i = 20; i < celsius; i++) {      steps++;    }    g = g - (steps * 17);  }  // wenn Temperatur über 35  if (35 < celsius) {    r = 255;    g = 255;    b = 0;  }

 colorWipe(strip.Color(r, g, b), 50);  strip.show();

}

PROJECT 3 Final Project | 4 weeks | Assessment: 25%

In this Final Project you will combine the tools and techniques picked up in the first two assignments, and combine them into a new project. You can propose an entirely new concept, unrelated to previous iterations of your work made in the first two assignments, or you can choose to continue the progress made from projects 1 & 2. In any case you will treat this final project as if it’s a new proposal, and create the appropriate documents including your research, ideation, topic of focus and production outlines. Additionally, throughout this assignment you will create and assemble documentation of your theoretical and technical work of this trimester, in written and audio-visual form –for which the details are outlined below.

Schedule:

• Create your final project contextualisation document. It should include: One paragraph description of your interface or interactive environment One paragraph description explaining how this project departs from earlier work in this course Visuals (sketches, diagrams, etc.) of your concept Hardware and software to be used Theoretical outline of technical concepts used in your design Visuals of any related previous work related to your proposal Your topic of focus (interface and/or mode of interaction) Your production focus Ideation: sketches, timeline, flowchart Timeline with milestones

• Each proposal will be assessed for its creative and artistic merit weighted against its achievable potential

• Proposals are reworked to accommodate set milestones

• Progress checks

• Present your design, a functional prototype and hand-in required material

Hand-in format:

• Submit to hand-ins drive: finalised proposal based on your research.

• Present finalised design and functional prototype in class (details of presentation to be discussed in class)

• Submit to hand-ins drive(to be discussed in more detail in class):

Serial Monitor:

1st: check Internet connection ---> DHCP:OK...Setup complete.