#foxflash ecu programmer

Foxflash ECU Programmer Customer Problem:

I can’t read id and flash?

Renault Trafic 1.6 Bosch EDC17C42

Tried via obd and also via bench mode, always same? Have this message: ERROR !!! contact support [email protected].

Eobdtool.co.uk engineer replied:

It cannot read via obd if there is no vr file in server.

double check wiring and voltage.

Foxflash will R/W in boot as well.

You may have problem with ecu.

Many customers read and write renault EDC17C42 by bench mode

R/W OK, Checksum OK.

Need to use Foxflash Bench Box, connect the power adapter to Foxflash or bench box are OK, there is no difference.

Reanult/Nissan TC1767 EDC17C42 Pinout to Foxflash ECU Chip Tuning Tool:

Pin Q4, D1: +12V (Red)

Pin J3: Brown

Pin H4: White

Pin H1: GND (Black)

Pin A1: CAN-H (Blue)

Pin A2: CAN-L (Orange)

To read and write use the following driver:

-> BENCH TRICORE

-> RENAULT or NISSAN

-> TC1767- RENAULT or NISSAN

-> EDC17 C42

If Foxflash ECU Tool read Renault EDC17C42 ECU on bench OK, but failed to write with the error “OTP sector not writable” as shown below.

The possible cause is that your file is bad.

Bad file tried to write the original file and see if all is ok.

Tutorial:

How to use Foxflash ECU Programmer and OTB 1.0 Expansion Adapter to read and write Mercedes-Benz CRD3 ECU via OBD driver?

What is foxFlash OTB 1.0 Expansion Adapter?

Foxflash OTB Adapter and Mercedes-Benz CRD3 ECU Pinout:

Need to connect the following 5 cables

CAN+: Pin 42

CAN-: Pin 55

+12V: Pin 5

GND: Pin 2

Ign: Pin 15

Check the corresponding Pin positions on Foxflash OTB Expansion Adapter

Then connect OTB Adapter and ECU correctly

Connect Foxflash and OTB 1.0 Adapter via OBD cable

Supply power to OTB Adapter as well

Read & Write ECU operation guide:

After connection, run Foxflash Manager and software

Select the driver and ECU you desire

For example:

Select CAR obd>> MERCEDES>> C KLASS>> 1.8/2.2 CDI Blue Delphi CRD3.x * CAN Fast

Enter the read and write interface

First, get ID

Then, read file and save the CRDF file

Next, open the CRDF-EGR DPF file

Last, write the file into the Mercedes-Benz CRD3ECU

Good news!! Foxflash has the latest update.

OBD VR file update: MED17.5.25 DCM6.2A DCM6.2V DCM6.2C PCR2.1 SIMOS18.1 EDC17C74

foxFlash Manager Update: FW update to D086 Notifications add

Checksum fix: Marelli 9DF Marelli MJD602.M1 - 603.S3 Bosch EDC17CP44

foxFlash OTB 1.0 Expansion Adapter is specially designed for foxFlash ECU Programmer extended application engine and transmission computers and ACM and DCM computer modules.

OTB expander package:

1PC OTB 1.0 expander

1SET OTB 1.0 conversion cable

1PC Paper Box

Adapter only, Foxflash hardware is not included.

For Foxflash ECU Chip Tuning Tool ONLY! Don't need to connect with bench box.

Don’t use it with PCMTuner ECU Programmer! Otherwise, the device will be damaged! (Illegal use can not be after-sales)

OTB= OBD mode via bench pinout (OBD on bench)

What can foxFlash OTB 1.0 Adapter do?

Dual-channel high-speed CAN

Three-way BOOT

Dual VCC power supply

GPT encryption and decryption function

Adaptive resistance

Adaptive CNF signal adjustment

Why does Foxflash team product this OTB 1.0 Expansion Adapter?

1.Ensure that foxFlash can be expanded to the OTB mode of BENCH PLUS in any OBD working mode

2.Achieve high-speed reading and writing

3.Ensure communication security and prevent the possibility of ECU brick due to voltage instability.

4.OTB reading and writing in OBD offline mode

5.ECM, TCM, ACM, DCM direct desktop mode reading and writing

6.Improve the reading and writing speed of some OBD drivers

Which car models can work with foxFlash OTB Adapter?

Visit https://www.dfb-technology.com/driver-list.html

Search for OTB to view the models and models that support OTB.

If the query mode cannot be displayed when opened, please clear the browser cache and reopen the website.

The foxflash OTB 1.0 Expander will be in stock after 2 weeks. If you are interested in it, please contact our customer service to pre-order it.

Email: [email protected]

WhatsApp: +86 159 7293 3706

Skype: Eobdtool.co.uk

Is it possible to read/write Citroen C4 Spacetourer MD1CS003 ECU with Foxflash ECU Programmer via OBD?

Here is the clue:

1.Before 2020 Bosch MD1CS003 BENCH! Try bench it, if locked, then no tool can do in the worldwide till now.

2.On the bench it works for sure.

3.Bench. Tested and is OK.

4.2021 bench OK.

Foxflash Citroen C4 Spacetourer MD1CS003 Bench Pinout Diagram:

BOSCH MD1CS003 [TC298TP]- Peugeot, Citroen [Diesel]

Use:

Multifunction cable

Bench Box V.2

To read and write use the following driver:

->BENCH MODE

->CITROEN/ PEUGEOT

->TC298TP- PSA

Here is the newest customer feedback about Foxflash ECU Chip Tuning Tool.

edc15 P+ BENCH Flash & eeprom Start

EDC15C3 (bench)– from Renault Laguna/ Read/Write OK

EDC15C13 (bench) — from Espace IV/ Read/ Write OK

EDC15C4 Full Flash R/W OK – obd-bench with 12v

edc15c13 renault BENCH Flash&eeprom Start

EDC16C1 E+F R/W OK – bench ok.

EDC16C9 bench R/W OK

EDC16C10 Read ok, Write ok, Checksum

Edc16c31 bmw bench r/w ok chck ok

EDC16CP31 BENCH DPF OFF R/W PERFECT

EDC16C3 R/W OBD CHECK OK

EDC16CP33 R/W OBD CHK INJCODE OK

Edc16c34 program disable while uploading, reads ok.

edc16u34. it worked reading and writing bench

EDC16CP35 READ/WRITE OK

EDC16C34 R/W OK Hardcut added & Car started perfectly psa

Edc16c39 can Read and write ok with obd Opel zafira B 1.9cdti 150cv

Edc16c39 fiat ducato obd R/W checksum ok

edc17c06 bmw BENCH, Read ok, Write ok, Checksum ok, car starts

edc17c08 bench ok

Edc17cp20 vag bench r/w ok chck okEcd17c70 obd ok

Edc17cp20, VR ok, write ok vw t6

Esc16c60 bench ok password unlock

EDC17CP01 V6 CDI Sprinter r/w ok bench

EDC7C3 bench r/w ok man bench

EDC17CP06 E+F R/W OK – bench

Edc17cp09 read/write ok chk ok

EDC17C10 Read ok, write OK, checksum ok bench

EDC17C11 bench R/W OK

EDC17Cp39 on Freelander 2 obd read write chk ok

EDC17C41_TC1797_ Bench bed written ok bmw

Edc17cv41 r/w cks ok.

edc17c42 bench R/W ok

Edc17cp44 bench read and write ok

EDC17CP45 BMW X6 D40 bench reading ok

edc17cp45 – “reading” (it is VR) via OBD. No file on DB but ID is working

Edc17c46 R/W bench OK!

edc17c50 TC 1797 BENCH r/w OK Mod Stage 1 with Display Calibration

EDC17CP54 on bench r/w all fine and easy. Cheksum with Winols.

Edc17c56 read ok Bench

edc17c59 BENCH Read ok, write OK, checksum ok opel

edc17c60 psa bench r/w ok

EDC17C64 bench R/W OK

Edc17c66 Mercedes r/w ok bench

Edc17c69 Iveco bench r/w ok chck ok

EDC17C79 Jeep Grand Cherokee full RW include checksum works OK

Edc17c84 r/w ok bench

EDC17C84 Opel vivaro 2018 with system adblue. with module 71

Delphi DCM3.5 R/W OK in JTAG

Dcm6.1 ford(psa) obd r/w ok chck ok

Dcm 6.2 obd ok

DCM6.2V Audi A3 2017 VR/Write ok

Dcm 7.1 boot ok

Crd2 Mercedes not work- read obd WRITE OBD FAIL- r/w ok by jtag

CRD3.10 Full bench read/write (flash+eprom) + auto checksum

Simos 8.10  obd  or boot car not start ecu problem

MEV17.4.2 READ MOD WRITE

ME 7.5 Full R/W , Stage1 all OK

Me7.6.2 opel bench r/w chck ok

ME7.6.3 Bench reading ok

MED9.1 bench R/W OK

medc17 bench R/W ok

MED17.2.5 R/W Ok Seam’s like a stable & Reliable tool, very Internet dependant.

Med 17.5.5 VW Scirocco 1.4 TSI 160CV Bench R/W – OK!

Med 17.7.7 Mercedes r/w ok bench

ME 17.9.6 read flash + eeprom ok

PCR2.1 Read MCU ID, ,Bench mode R/W, Online Patch unlock OBD, Checksum

MD1CP001 MB W213 2018y R/W OK , checksum calculated from the original file.

MD1CP014 bench r/w ok

MD1CS004 read + write OK audi

md1cs003 psa bench ok

Md1cs006 renault r/w ok bench

Mg1cs201 r/w bench ok

Mg1cs003 r/w bench ok

SID201 via OBD, success EGR OFF, read/write + checksum ok

sid206 obd read/write ok

Sid208 r/w ok

SID211 OBD OBDFORD TRANSIT ok

SID 305 tricore 1766 Micro Read/Write Boot Mode ok STG 1 DPF, EGR, DTC OFF.

SID310 READ PASSWORD, READ FLASH,READ EEPPROM, DTC OFF, FLASH WRITE, CHECKSUM

Sid803A PSA full system Clone done. Read in 15min, Write in 15min, Car Start

SID807 evo obd read ok, write mod ok. CHK MANUAL, program did not ask if it should correct or not

PCR2.1 obd vr/unlock/w ok

E83 full mode R/W dtc off, CS ok with ori file

E97 full system R/W ok

E98 bench r/w ok

MB175800 Denso Works Perfectly:)

New Added Functions: Boot Read Boot Write

New Added ECU List: Continental GPEC2, GPEC3, GPEC4LM, GPEC2A

How to update FoxFlash Software? Run the FoxFlash Manager, and click the "Download" button until all is done.

Good news!! foxFlash 25.02 update protocols for Porsche PDK and now you can easily read and write Porsche PDK gearbox!

Supported Control Units & Vehicles:

BOOT Porsche 911.2 Siemens PDK4000 Porsche 918 Siemens PDK3000 Porsche 918 Siemens PDK4000 Porsche Boxster 718 Siemens PDK3000 Porsche Boxster 981 Siemens PDK4000 Porsche Carrera 991 Siemens PDK3000 Porsche Carrera 991 Siemens PDK4000 Porsche Cayman Siemens PDK4000 Porsche Macan Siemens PDK3000 Porsche Macan Siemens PDK4000 Porsche Panamera Siemens PDK3000 Porsche Panamera Siemens PDK4000